User manual KENWOOD CAW-FT7050

[. . . ] Therefore always obey the local traffic signs and regulations rather than the system's instructions. Failure to do so may place you in illegal, unsafe or dangerous situations. DRIVE SAFELY. Before following the system's guidance instructions, such as changes in direction, always check first whether it is safe to do so given the current traffic conditions. Then follow the given instructions, but make sure you do so in a safe manner. VOLUME LEVEL. Keep the system's volume at a low enough level to be able to hear outside noises whilst driving. If you can no longer hear outside noises, you may be unable to react adequately to the traffic situation. [. . . ] (See below) Quick POI Selection ································Allows you to select the categories on the menu POI displayed when has been selected on the Current Position screen. Restore System Defaults ·······················Allows you to return all the settings in the navigation system to the initial default settings. (See page 29) Vehicle Signal··········································Allows you to check the condition of signals that are connected to the navigation system. (See page 30) Calibration ···············································Allows you to correct any error in the vehicle display position or direction. (See page 30) Map Version ············································Allows you to check the version of the map disc you are currently using. (See page 31) 2D/3D View ············································· Allows you to switch between a 2D and 3D display screen. (See page 32) Average Speed Settings You can display a more accurate estimation of the time required (see page 34) by setting the predicted average driving speed on each category of road. Menu (Navigation Set Up) 1 2 3 Select Select Select OK (Average Speed Settings). . NOTE : Default ·······Returns the average speed setting to the initial default setting. Quick POI Selection ENGLISH This function allows you to set the categories on the menu displayed when POI (Point of Interest) is selected on the map. (See page 42 for how to display markers on the map and search for nearby points of interest) Menu (Navigation Set Up) (Quick POI Selection). 1 2 Select Select a switch to change the POI category. 3 Select the POI you want to display on the menu. 4 Select OK . · Repeat the above steps 1 to 4 to add further POI markers displayed on the menu. Restore System Defaults This function replaces all the settings in the mobile navigation system with the initial default settings. Menu (Navigation Set Up) (Restore System Defaults). OK 1 2 Select Select . IMPORTANT : If you execute Restore System Defaults, all of your Stored Locations data will be deleted. 29 Vehicle Signal ENGLISH 30 In this screen you can check the navigation connections. The Reverse (REV) and Speed-pulse (SPD) connections are necessary for accurate calibration and functionality. Menu (Navigation Set Up) (Vehicle Signal). 1 Select REV. : With the reverse signal wire connected and with reverse gear selected, the REV indicator will change to `ON'. (Destinations) ··············This deletes previously stored destinations (and way points). (Destination and Way Point) ·······························································This sets the destination (and way points). 4 Select Add . You can display the map of the area you require by selecting one of the methods on the screen. · See page 16 for how to access maps. 35 · Select the editing method you require from (Delete All). Add List Add , List , Delete and Del. All ENGLISH ·········This is for storing a new location. ·········This is for displaying the list of stored locations. Delete ·········This is for deleting stored locations. All ·········This is for deleting all stored locations. The switches displayed vary according to the item. (See below) Memory Points (100) Add List Delete Del. All Previous Destinations (20) Delete Del. All Home (1) Add List Delete Dest. (Destination & Way Point) (Destination: 1, Way Point: 5) Add List Delete Del. [. . . ] (15) The system might not use a ferry boat even if it is located nearby. (16) If the guided intersection is near the end of the route search, the system might not be able to provide guidance. (17) The route might not go on a toll road even the toll-road priority is selected. Similarly, a route that uses a toll road could appear on the screen even if the tollroad priority is not selected. [. . . ]