User manual KENWOOD DDX7031BT

[. . . ] If the program that is activated when the . . . . . . . . . . 6 2 DNX SERIES/ DDX SERIES    FFPKJUKNIP'A/AA$ product is first powered on works properly, the front panel will automatically move into the position (initial setting angle) shown in (Fig. 2) After the Installation After the installation, perform the Initial Setup by referring to the instruction manual. ¤ • Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals. • Make sure to ground the unit to a negative 12V DC power supply. [. . . ] Also avoid places with too much dust or the possibility of water splashing. If you use the wrong screws, you could damage the unit. • If the power is not turned ON (“PROTECT” is displayed), the speaker wire may have a shortcircuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. • If your car’s ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. • If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. • If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. It should be installed as horizontally as possible to allow easy reception of the GPS satellite signals. To mount the GPS antenna inside your vehicle: 1. Peel the backing off of the adhesive on the bottom of the metal plate (accessory $). Press the metal plate (accessory $) down firmly on your dashboard or other mounting surface. You can bend the metal plate (accessory $) to conform to a curved surface, if necessary. Place the GPS antenna (accessory #) on top of the metal plate (accessory $). Accessory ! Accessory # Accessory $ Fix a cable with a commercial item of tape. Peel the release coated paper of double-face adhesive tape to fix on the place shown above. ¤ • Depending on the type of car, reception of the GPS satellite signals might not be possible with an inside installation. • The GPS antenna should be installed at a position that is spaced at least 12 inch (30 cm) from cellular phone or other transmitting antennas. Signals from the GPS satellite may be interfered with by these types of communication. • Painting the GPS antenna with (metallic) paint may cause a drop in performance. Adjust the direction of the microphone to the driver. ⁄ 8 DNX SERIES/ DDX SERIES Install the microphone as far as possible from the cell-phone.    FFPKJUKNIP'A/AA$ Installing the Escutcheon For General Motors 1. Cut out accessory 6 to meet the shape of the opening of the center console. Attach accessory 6 to the unit. Cut out to meet the shape of the opening in the vehicle. For Toyota/Scion 1. [. . . ] Cut out accessory 6 as illustrated. Cutting line Accessory 6 Accessory 6 For Volkswagen 1. Fold double-sided adhesive (accessory 7) along the slit and attach it to accessory 6 cut-out against the center rib as illustrated. Use 2 pieces of accessory 7 for 1 accessory 6 cut-out. Attach accessory 6 cut-out to the unit. Accessory 7 Accessory 0 English 9    FFPKJUKNIP'A/AA$ Installation for Monitor/Player Unit Installation the Monitor/Player unit Attaching the monitor panel Accessory @ Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. ⁄ • Make sure that the unit is installed securely in place. [. . . ]