User manual KENWOOD DPC-761

[. . . ] · Do not watch or fix your eyes on the unit's display when you are driving for any extended period. · Mounting and wiring this product requires skills and experience. For safety's sake, leave the mounting and wiring work to professionals. About CD players/disc changers connected to this unit Kenwood disc changers/ CD players released in 1998 or later can be connected to this unit. Refer to the catalog or consult your Kenwood dealer for connectable models of disc changers/ CD players. [. . . ] "MENU" is displayed. 2 Select the menu item Push the Control knob towards up or down. Example: When you want to set the beep sound select the "BEEP" display. 3 Set the menu item Push the Control knob towards right or left. Example: When you select "BEEP", each time you push the knob it alternates between "BEEP ON" or "BEEP OFF". You can continue by returning to step 2 and setting other items. 16 | English In Standby mode Activating Security Code Activating the Security Code disables the usage of audio unit by someone else. Once the Security Code is activated, the entry of authorized Security Code is required to turn on the audio unit when it is removed from the vehicle. Indication of this Security Code activation prevents your precious audio unit from stealing. Resetting the Security Code function when the audio unit is first used after removed from the battery power source or the Reset button is pressed 1 Turn the power ON. 2 Do the step 4 through 7 operation, and enter the Security Code. Now, you can use the unit. / · You can set the Security Code with a 4 digit number of your choice. · The Security Code cannot be displayed or referenced. Make a note of the Security Code and treasure it up. / · When the Security Code function is activated, "CODE SET" changes to "CODE CLR". · To deactivate the Security Code function, see the next section <Deactivating Security Code>. 1 Enter Standby Press the [SRC] button. Display "AMP ON" "AMP OFF" Setting The built-in amplifier activates. The built-in amplifier deactivates. / · Set the Display Illumination Control when the <Demonstration mode Setting> (page 21) is set to OFF. · When the display is off, pressing any key will turn on the display. 18 | English In Audio file source In HD Radio mode Supreme Setting When AAC, MP3 or WMA files encoded at a low bit rate (less than 96kbps (fs=44. 1k, 48kHz)) are played, this function restores their high frequency region to approach the sound quality of equivalents of these files encoded at a high bit rate. Processing is optimized for the compression format used (AAC, MP3, or WMA), and adjustment is made for the bit rate used. Display "SPRM ON" "SPRM OFF" Setting Plays sound using the Supreme function. Plays the original sound stored in the audio file. Receive mode Setting Sets the receive mode. 1 Select the Receive mode Push the Control knob towards up or down. Select the "HDR MODE" display. 2 Enter Receive mode Press the Control knob for at least 1 second. 3 Set the Receive mode Push the Control knob towards up or down. Each time you push the knob, the Receive mode alternates between the modes shown in the table below. Receive mode Auto mode Display "AUTO" Operation Analog broadcasts and digital broadcasts will be switched automatically. When both are being transmitted, the digital broadcast will have priority. Analog broadcasts only. / · The sound effect may be imperceptible depending on the relationship between the audio file format and setting. In FM reception CRSC (Clean Reception System Circuit) Temporarily have reception alternate from stereo to mono to reduce multi-path noise when listening to the FM station. [. . . ] The Touch Sensor Tone can't be output from the preout jack. Tuner source ? Radio reception is poor. The antenna control wire is not connected. Connect the wire correctly, referring to the section on <Connecting Wires to Terminals> (page 25). English | 29 Troubleshooting Guide The messages shown below display your systems condition. EJECT: · No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. [. . . ]