User manual KENWOOD DPX-5010

[. . . ] DPX-5010 DOUBLE DIN SIZED CD/CASSETTE RECEIVER INSTRUCTION MANUAL Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new double din sized CD/cassette receiver. Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product. [. . . ] · The default setting is "Medium". 1 Press the DSP button. "DSP CTRL" is displayed once the DSP control mode is entered. The DSP indicator blinks during the DSP control mode. 4 Press the DSP button to end the DSP control mode. -- 23 -- DSP features English DSP Setting Preset Memory Up to three sets of the DSP settings and conditions you adjusted can be stored in the memory, and then you can recall them with the single touch of a button. Graphic Equalizer features EQ CD OPEN/CLOSE TAPE OPEN/CLOSE SRC DIGITAL SIGNAL PROCESSOR 1 Press the DSP button. "DSP CTRL" is displayed once the DSP control mode is entered. The DSP indicator blinks during the DSP control mode. DSP 7 OFF DPX-5010 7 OFF PWR 2 Make the DSP settings and adjustments that you want to store in the memory. VOLUME LAST ANGLE MEMORY 7 SBF RETURN ANGLE 3 Press the button (#1-3) that you want to use for the DSP settingsand adjustments for at least two seconds. The button number blinks once in the display to indicate that the data has stored. ATT EQ 7 CRSC FNC 7 NAME. S DISP SCROLL B NR 77 SCN 78 79 COMPRESSION KBS RDM/B. S REP 70 SFC DBB SFC LEVEL D. S POSITION ROOM SIZE M. RDM/MTL , DIGITAL X OVER FM+ DISC AM­ 4 Press the DSP button to end the DSP control mode. Recalling a DSP settings and adjustments you stored: 1 Press the DSP button. "DSP CTRL" is displayed once the DSP control mode is entered. The DSP indicator blinks during the DSP control mode. 1 DIS DIR 2 CD IR EC T 3 4 5 6 CD CASSETTE DSP RECEIVER PROGRAM AUD DISP #1 2 Press the preset button (#1-3) for the desired DSP settings and adjustments. #2 #3 KBS #5 #6 4 ¢ AM FM 3 Press the DSP button to end the DSP control mode. KBS name/Spectrum analyzer name/Equalizer frequency and level display Equalizer/Analyzer display -- 24 -- Graphic Equalizer This mode allows you to call up the preset equalizer curves, adjust the graphic equalizer, make the setting of the spectrum analyzer, and so on. Turning the Graphic Equalizer Mode On: Press the EQ button. "EQ CTRL" is displayed once the Graphic equalizer mode is entered. NOTE equalizer mode is entered. The preset equalizer name currently set appears in the display. 2 Each time you press the 4 or ¢ button, the selectable frequency band switches as follows; "60 Hz" j "120 Hz" j "250 Hz" j "500 Hz" j "1 kHz" j "2 kHz" j "4 kHz" j "8 kHz" j "16 kHz" 3 Press the FM or AM button. Press the FM button to increase the equalizer level, and the AM button to decrease it. There are six levels for both plus and minus allowing each band to be set to one of 13 steps. Be sure to turn the GraphicEqualizer mode on when performing the operations described below in the Graphic Equalizer features. Turning the Graphic Equalizer Mode Off: Press the EQ button. NOTE 4 Press the EQ button to end the Graphic equalizer mode. Graphic Equalizer Preset Memory Up to three graphic equalizer curves can be stored in the memory, and then you can recall that equalizer curve with a single touch of a button. If you make no button operation for 10 seconds, the Graphic equalizer mode is automatically canceled. Preset Equalizer (KBS - Kenwood Built-in Sound) Selection You can choose the equalizer from five settings whose sound qualities are preset to match music or vehicle characteristics. Switching the Preset Equalizer: 1 Press the EQ button. "EQ CTRL" is displayed once the Graphic equalizer mode is entered. The preset equalizer name currently set appears in the display. 1 Press the EQ button. "EQ CTRL" is displayed once the Graphic equalizer mode is entered. The preset equalizer name currently set appears in the display. 2 Adjust the graphic equalizer curve that you want to store in the memory. 3 Press the button (#1-3) that you want to use for the Graphic Equalizer curve for at least two seconds. The button number blinks once in the display to indicate that the data has stored. 2 Each time you press the KBS button, the preset equalizer switches as follows; "Rock" "Pops" "Dance" "Vocal" "Flat" 4 Press the EQ button to end the Graphic equalizer mode. Recalling a GraphicEqualizer curve you stored: 1 Press the EQ button. "EQ CTRL" is displayed once the Graphic equalizer mode is entered. The preset equalizer name currently set appears in the display. 3 Press the EQ button to end the Graphic equalizer mode. [. . . ] An attempt was made to display the track/disc title of the CD during play, but the CD has no texts. The MD you tried playing is designed for use with data. ] Eject the MD designed for data and load the one designed for music. ] Eject the tape and try inserting it again. [. . . ]