User manual KENWOOD DPX-600

[. . . ] · The RDS feature won't work where the service is not supported by any broadcasting station. · The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may be inapplicable. Before using this unit for the first time This unit is initially set on the Demonstration mode. When using this unit for the first time, cancel the <Demonstration mode Setting> (page 12). How to reset your unit · If the unit fails to operate properly, press the Reset button. [. . . ] Select the "CLK ADJ" display. 7 Confirm the Security Code Press the center of the Control knob for at least 3 seconds. When "RE-ENTER" is displayed, "CODE" is also displayed. 3 Enter Clock Adjust mode Press the center of the Control knob for at least 1 second. The clock display blinks. 8 Do the step 4 through 7 step operation, and reenter the security code. The Security Code function activates. 4 Adjust the hours Press the top or bottom side of the Control knob. Adjust the minutes Press the right or left side of the Control knob. / · If you enter a Code different from your Security Code, you have to start over from step 4. 9 Exit Security Code mode Press the [B. BOOST] button. 5 Exit Clock adjustment mode Press the [B. BOOST] button. / · You can do this adjustment when the "SYNC" is set as "OFF". English | 11 Menu Operation Auxiliary Input Display Setting Selecting the display when changing to Auxiliary input source. In Standby mode Demonstration mode Setting Sets the demonstration mode. 1 Select Auxiliary input source Press the [SRC] button. Select the "AUX" display. 1 Enter Menu mode Press the [B. BOOST] button for at least 1 second. "MENU" is displayed. 2 Enter Menu mode Press the [B. BOOST] button for at least 1 second. "MENU" is displayed. 2 Select the Demonstration mode Press the top or bottom side of the Control knob. Select the "DEMO" display. 3 Select Auxiliary input display setting mode Press the top or bottom side of the Control knob. Select the "NAME SET" display. 3 Set the Demonstration mode Press the center of the Control knob for at least 2 seconds. Each time you press the knob at least 2 seconds, the Demonstration mode alternates between the settings shown in the table below. · AUTO1, AUTO2, MANUAL (Tuning mode select) Select a tuning mode of the radio. Tuning mode Display Auto seek "AUTO 1" Preset station seek "AUTO 2" Manual Operation Automatic search for a station. Search in order of the stations in the Preset memory. "MANUAL" Normal manual tuning control. Menu Glossary · SWPRE (Switching Preout) Switches the preout between rear output ("R") and subwoofer output ("SW"). · SPRM (Supreme) Technology to extrapolate and supplement with proprietary algorithm, the high-frequency range that is cut off when encoding at low bit rate. Supplementing is optimized by compression format (MP3 or WMA) and processed according to bit rate. The effect is negligible with music that is encoded at high bit rate, variable bit rate or has minimal high frequency range. · CD READ Sets the method for reading CD. When unable to play special format CD, set this function to "2" to force playing. Note that some music CD may be unplayable even when set to "2". In addition, audio files cannot be played when set to "2". [. . . ] 3 Insert the two removal tools deeply into the slots on each side, as shown. 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Screw (M4X8) (commercially available) Accessory2 ¤ · Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. 18 | KDC-W3541/KDC-W3041/DPX-600/KDC-W241/KDC-241 Troubleshooting Guide Some functions of this unit may be disabled by some settings made on this unit. The messages shown below display your systems condition. TOC ERR: · No disc has been loaded in the disc magazine. Media was played that doesn't have data recorded that the unit can play. The unit is malfunctioning for some reason. If the "E77" code does not disappear, consult your nearest service center. [. . . ]