User manual KENWOOD ECOROUTE BROCHURE

[. . . ] For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse. The fuse cover must be refitted when replacing the fuse in the moulded plug. Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer. [. . . ] To prevent this, press the 7 (stop) key immediately after pressing CD 6 or TAPE 23. Selecting digital-to-digital or 1 (Applicable only for recordinganalog-to-digital recording (Rec Input) from CD player) 1 Press the MENU key. MENU Application section ÷ Digital-to-digital recording from CD may sometimes be prohibited by the SCMS (A). In this case, select "Ana. ". 2 Press a MULTI CONTROL keys to select "Rec Input ?" and press the SET key. # MULTI CONTROL Rec Input? DIGITAL \ SET # Blinks 3 Press a MULTI CONTROL keys to select "Dig. " (digital-to-digital recording) or "Ana. " (analog-todigital recording) and press the SET key. MULTI CONTROL Knowledge section When "Dig. " is selected, the setting is complete. When "Ana. " is selected, go to step 2-3 # \ SET ÷ The "DIGITAL" indicator lights when "Dig. " is selected. The "DIGITAL" indicator does not light when "Ana. " is selected. ÷ During digital-to-digital recording, the track number is incremented automatically by "1" according to digital data, so the blank is not detected. Note that, if the track number changes during fast forward or backward operation, the CD recorder may not be able to change the recorded track number correctly. Also, when the player CD is stopped, a nosound track may sometimes be created. # Continued on next page 44 Recording on TAPE Changing the recording input setting 2 Selecting the track number marking method (T. Mark) The track numbers are used in playback for locating the beginning of a song, programming, etc. Preparation section 1 Press the MENU key. MENU 2 Press a MULTI CONTROL keys to select "T. Mark ?" and press the SET key. MULTI CONTROL 3 Press a MULTI CONTROL keys to select "Auto" or "Manual" and press the SET key. # \ SET T. Mark Auto "Auto" . . . . . . . . . . . . Track numbers are marked automatically during recording. Track numbers are marked manually during recording. Basic section # # MULTI CONTROL When "Auto" is selected: When the input source is "CD", the setting is complete. When the input source is "TAPE", "TUNER" or "AUX", go to step 3. in the order you want to play them. 1 Select a track number using numeric keys. Go to step 2 within 20 sec. 1 2 3 1 Track selection Blinks PGM 2 Programming Application section PGM 4 5 6 7 8 9 CD TOTAL 08 P-01 \ CD TOTAL 08 P-01 0 +10 REMAIN REMAIN Press the numeric keys as shown below. . . . +10, +10, 0 2 Press the SET key. SET ÷ After the adjustment, the time display appears again. ÷ The track can also be selected using the 4 or ¢ key. ÷ Up to 32 tracks can be programmed. When "PGM Full" is displayed, no more tracks can be programmed. ÷ If you do not press the SET key before the track number display stops blinking, the track number entry is canceled. 3 Repeat steps 1 and 2. Knowledge section 4 Start playback. Press the CD 6 key. CD 6 ÷ Tracks will be played in the order they were programmed (in order of PGM-Nos. ). ÷ When the 4 or ¢ key is pressed during play, the program will jump to the preceding or the following track respectively. ÷ When the 4 key is pressed once during playback, the play position returns to the beginning of the current track being played. 48 Various playback features Preparation section To add a track to the program (Remote control unit only) Press in stop mode 1 Select the track number to be added using the numeric keys. 1 2 3 PGM CD TOTAL 4 5 6 02 P-03 Blinks Basic section 7 8 9 REMAIN 0 +10 Press the numeric keys as shown below. . . . +10, +10, 0 2 Press the SET key. SET ÷ The track can also be selected using the 4 or ¢ key. ÷ Up to 32 tracks can be programmed. [. . . ] W : 243 mm (9-9/16") H : 284 mm (11-3/16") D : 310 mm (12-3/16") Weight (net) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. 3 kg (13. 9 lb) Preparation section Basic section [Tuner section] FM tuner section Tuning frequency range . . . . . . . . . . 87. 5 MHz ~ 108 MHz MW (AM) tuner section Tuning frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531 kHz ~ 1, 602 kHz [CD player section] Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]