User manual KENWOOD KCH-16

[. . . ] For a detailed explanation on the operations, refer to the Transceiver's instruction manual. © B62-2101-00 (M) · Do not use options not specified by Kenwood. · Use of the KCH-16/ transceiver while you are driving may be against traffic laws. Please check and observe the vehicle regulations in your area. q Power switch Press to switch the transceiver ON. Press and hold for approximately 1 second to switch the transceiver OFF. w Display e Right (Zone Up) key Press to increase the zone number (Default setting). [. . . ] !0 TX/ BUSY indicator The TX/ BUSY indicator lights red while transmitting and green while receiving. PTT (Push-To-Talk) switch Press and hold this switch, then speak into the microphone to call a station. HOOK Display UNPACKING AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. FEATURES · The KCH-16 is a full-control optional microphone for use with the TK-5710/ 5810 P25/ FM analog Dual Mode transceiver. · By connecting the KCH-16 to the optional KRK-11 handheld control head interface kit, you can control the transceiver using the microphone in the same way that the KCH-14/15 can be used. Carefully unpack the Handheld Control Head. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately. Indicator NOTICES TO THE USER Government law prohibits the operation of unlicensed transmitters within the territories under government control. Illegal operation is punishable by fine and/or imprisonment. Refer service to qualified technicians only. Supplied Accessories Item Hanger (with 4 x 16 mm self-tapping screws) Instruction manual Part Number J19-5482-XX B62-2101-XX Quantity 1 set 1 One or more of the following statements may be applicable: FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer for technical assistance. SPECIFICATIONS Operating temperature range Microphone impedance Dimensions (W × H × D) -30 +60 2. 2 k (Max) without projections 58 × 125 × 31. 5 mm 2. 3 × 4. 9 × 1. 2 inches 68 × 125 × 36 mm with projections 2. 7 × 4. 9 × 1. 4 inches Cable not included Approx. 280 g / 9. 9 oz Weight GETTING AQUAINTED Handheld Control Head 12 Description Displays the operating zone and channel numbers or zone and channel names. Also displays various text messages depending on the function being used. Displays various characters depending on dealer settings. [. . . ] Appears when the Auto Reply Message on the VGS-1 option is activated. (The location of this icon is the same as the Auto Recording icon. ) 9 10 Microphone Key name (function) comparison (in regards to the KCH-14/ KCH-15) PRECAUTIONS Observe the following precautions to prevent fire, personal injury, and KCH-16/ transceiver damage. · Do not drop the KCH-16; strong impacts can damage the internal components. 1 2 11 9 4 7 8 3 5 6 · Do not over stress the KCH-16 cable by pulling on it with excessive force. · Do not disassemble or modify the KCH-16/ transceiver for any reason. · Do not attempt to configure the KCH-16/ transceiver while driving; it is too dangerous. · Do not expose the KCH-16/ transceiver to long periods of direct sunlight, nor place it near heating appliances. · If an abnormal odor or smoke is detected coming from the KCH-16 or transceiver, switch the KCH-16/ transceiver power off immediately, and contact your Kenwood dealer. KCH-14 GRP GRP (Zone Up) (Zone Up) GRP GRP (Zone Down) (Zone Down) CH (Channel CH (Channel) Up/Down) MON (Monitor) SCN (Scan) PF 1 PF 1 (None) PF 2 PF 2 (None) PF 3 PF 3 (None) PF 4 PF 4 (None) PF 5 PF 5 (None) PF 6 PF 7 PF 8 PF 9 KCH-15 GRP (Zone Up) KCH-16 Right (Zone Up) Left (Zone Down) GRP (Zone Down) CH(Channel Up/Down) MON (Monitor) SCN (Scan) PF 1 (None) PF 2 (None) PF 3 (None) PF 4 (None) PF 5 (None) PF 6 (None) PF 7 (None) PF 8 (None) PF 9 (None) The numbers of bars indicates the strength of incoming signals. The antenna plus 3 bars represents a strong signal while only the antenna represents a weak signal. [. . . ]