User manual KENWOOD KDC-1011S

[. . . ] Frequency Offset AMP Control Traffic Information CRSC (Clean Reception System Circuit) Receive mode Setting SIRIUS ID (ESN) display Auxiliary Input Display Setting & Station/Disc Naming Text Scroll Built-in Auxiliary input Setting CD Read Setting Picture downloading Voice Index ACDrive firmware version display Unique ID display Audio Preset Memory Audio Preset Recall Demonstration mode Setting 41 Basic Operations of remote control 55 Accessories/ Installation Procedure 58 Connecting Wires to Terminals Installation Removing the Unit Troubleshooting Guide Specifications 59 60 62 63 67 The "AAC" logo is trademark of Dolby Laboratories. English | 3 Safety precautions 2 WARNING To prevent injury while using this product, take the following safety precautions: · To prevent a short circuit and possible fire, never put any metallic objects (such as coins or metal tools) inside the product. · If you are the driver and your vehicle is moving, do not watch the product's display or use its controls for an extended period. · Do not use this product in any way that prevents you from driving safely. [. . . ] Refer to <Notes on Multi-function Key System> (page 11). 36 | English SIRIUS tuner control features Control knob AUTO NEXT 1­6 SRC Band display Channel number Select SIRIUS Satellite Radio Mode Selecting the SIRIUS Satellite Radio Tuner (optional accessory) connected to this unit. Switching Seek Mode Sets the seeking mode. Each time you press the button, the Seek mode alternates between the operations shown in the table below. Display Operation "Seek Mode Channel" Normal manual seeking control. "Seek Mode Preset" Search in order of the channels in the Preset memory. Selecting SIRIUS Mode Press the [SRC] button. Select the "SIRIUS" display. · You need to subscribe to SIRIUS to receive the service by SIRIUS Satellite Radio. Consult SIRIUS if "CALL 888539-SIRIUS TO SUBSCRIBE" appears. · The radio may take a little time to start receiving after you select the SIRIUS source. · If the signal reception fails, "Acquiring Signal" appears. Select the channel Selecting the channel. Push the Control knob towards [4] or [¢]. English | 37 SIRIUS tuner control features Category and Channel Search Selecting the channel and category you want to receive. · You cannot search for a channel number which is not broadcasting. (KTC-SR902/KTC-SR903: optional accessory) · If you cannot receive any signal in the input Channel due to bad conditions on radio wave or other such problems, "Acquiring Signal" appears. 1 Enter Category and Channel Search mode Press the Control knob. 2 Select the Category Push the Control knob towards [FM] or [AM]. Selecting the Preset Band · It is the item when the category of Middle text display part is selected. 3 Select the Channel Push the Control knob towards [4] or [¢]. Push the Control knob toward [FM]. Each time you push the knob, the preset band alternates between the SR1, SR2, SR3 and SR4. Channel Preset Memory · You cannot Channel search until the category information is acquired. Putting the channel in the memory. Cancelling Category and Channel Search mode Press the Control knob. 1 Select the preset band Push the Control knob toward [FM]. 2 Select the channel to put in the memory Push the Control knob towards [4] or [¢]. Function of remote control 3 Select the key function section Press the [NEXT] button. "MENU" is displayed. 2 Select the menu item Push the Control knob towards [FM] or [AM]. Example: When you want to set the beep sound, select the "Beep" display. 3 Set the menu item Push the Control knob towards [4] or [¢]. Example: When you select "Beep", each time you push the knob it alternates between "Beep : ON" or "Beep : OFF". English | 41 Menu system In Standby mode Activating Security Code Activating the Security Code disables the usage of audio unit by someone else. Once the Security Code is activated, the entry of authorized Security Code is required to turn on the audio unit when it is removed from the vehicle. Indication of this Security Code activation prevents your precious audio unit from stealing. · If you enter the wrong Code in steps 4 through 6, repeat from step 4. Resetting the Security Code function when the audio unit is first used after removed from the battery power source or the Reset button is pressed 1 Turn the power ON. 2 Do the step 4 through 7 operation, and enter the Security Code. Now, you can use the unit. · Set the Security Code when the <Demonstration mode Setting> (page 54) is set to OFF. · You can set the Security Code with a 4 digit number of your choice. · The Security Code cannot be displayed or referenced. Make a note of the Security Code and treasure it up. 1 Enter Standby Press the [SRC] button. [. . . ] If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted, please switch off the power and consult your nearest service center. No Device: The USB device is selected as a source although no USB device is connected. Change the source to any source other than USB. Connect an USB device, and change the source to USB again. [. . . ]