User manual KENWOOD KDC-234SG

[. . . ] KDC-234SG CD-RECEIVER INSTRUCTION MANUAL © B64-3245-00/00 (E2W) B64-3245-00_E_English. indd 1 05. 8. 2 5:25:17 PM Contents Safety precautions Notes About CDs General features Power Selecting the Source Volume Attenuator System Q Audio Control Audio Setup Speaker Setting Clock Display Adjusting Clock Theft Deterrent Faceplate TEL Mute 3 4 5 6 Accessories/ Installation Procedure 14 Connecting Wires to Terminals Installation Removing the Unit Troubleshooting Guide Specifications 15 17 18 19 21 Tuner features Tuning Tuning Mode Station Preset Memory Auto Memory Entry Preset Tuning Monaural Reception 10 CD player features Playing CD Fast Forwarding and Reversing Track Search Track Repeat Scan Play Random Play 12 2 | English B64-3245-00_E_English. indd 2 05. 8. 2 5:25:18 PM Safety precautions 2WARNING To prevent injury or fire, take the following precautions: • To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. Lens Fogging When you turn on the car heater in cold weather, dew or condensation may form on the lens in the CD player of the unit. Called lens fogging, this condesnation on the lens may not allow CDs to play. In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a while, consult your Kenwood dealer. 2CAUTION To prevent damage to the machine, take the following precautions: • Make sure to ground the unit to a negative 12V DC power supply. [. . . ] The "CALL" display disappears and the audio system comes back ON. The "CALL" display disappears and the audio system comes back ON. English | 9 B64-3245-00_E_English. indd 9 05. 8. 2 5:25:21 PM Tuner features Control knob MONO SRC 1–6 Band display Frequency display AUTO indicator ST indicator Preset station number Monaural indicator Tuning Selecting the station. Tuning Mode Choose the tuning mode. Each time you press the knob, the Tuning mode alternates between the modes shown in the table below. Tuning mode Display Operation Auto seek "AUTO 1" Automatic search for a station. indicator Preset station seek "AUTO 2" Search in order of the stations indicator in the Preset memory. Manual — Normal manual tuning control. 1 Select tuner source Press the [SRC] button. Select the "TUnE" display. 2 Select the band Push the Control knob towards [FM] or [AM]. Each time you press the button, the Track Repeat turns ON or OFF. When the Track Repeat is ON, the "REP" indicator is ON. Scan Play Playing the first part of each song on the disc you are listening to and searching for the song you want to hear. 1 Start Scan Play Press the [SCAN] button. "SCN" indicator is ON. 2 Release the button when the song you want to hear is played Press the [SCAN] button. Random Play Playing all the songs on the disc in random order. Each time you press the button, Random Play turns ON or OFF. When the Random mode is ON, the "RDM" indicator is ON. • When you push the Control knob toward [¢], the next random song starts. English | 13 B64-3245-00_E_English. indd 13 05. 8. 2 5:25:22 PM Accessories/ Installation Procedure Accessories 1 . . . . . . . . . . 1 2 . . . . . . . . . . 2 3 . . . . . . . . . . 1 • If the power is not turned ON (or it is ON, but will be OFF immediately), the speaker wire may have a short-circuit or touched the chasis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. • If your car is not prepared for this special connectionsystem, consult your Kenwood dealer. • Only use antenna conversion adapters (ISO-JASO) when the antenna cord has an ISO plug. • Make sure that all wire connections are securely made by inserting jacks until they lock completely. • If your vehicle’s ignition does not have an ACC position, or if the ignition wire is connected to a power source with constant voltage such as a battery wire, the power will not be linked with the ignition (i. e. , it will not turn on and off along with the ignition). If you want to link the unit’s power with the ignition, connect the ignition wire to a power source that can be turned on and off with the ignition key. • If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. [. . . ] ☞ Set the media you want to listen to. If there’s no media in this unit, you can’t switch to each source. The memory is erased when the ignition is turned OFF. ✔ The ignition and battery wire are incorrectly connected. [. . . ]