User manual KENWOOD KDC-C660

[. . . ] In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. KENWOOD CORPORATION 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0. 21 CFR 1040. Location : Bottom Panel NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Each time you press the button, the sound setting alternates. Sound setting Flat Rock Pops Easy Top 40 Jazz Display "FLAT" "ROCK" "POPS" "EASY" "TP40" "JAZZ" 5 Exit Audio Control mode Press any button. Press a button other than the [VOL] knob, [SRC], [0] and [ATT] button. Audio Setup Setting the Sound system, such as Volume offset and Loudness. · "USER": The values set on the <Audio Control> (page 8). When the System Q setting is changed, the Bass, Middle, and Treble set in audio control replace the System Q values. · Change each setting value with the <Speaker Setting> (page 9). First, select the speaker type with the Speaker setting. 1 Select the source to adjust Press the [SRC] button. 2 Enter Audio Setup mode Press the [VOL] knob for at least 1 second. 3 Select the Audio Setup item to adjust Press the [VOL] knob. Each time you press the knob, the item to be adjusted alternates between the items shown in the table below. Audio Control 1 Select the source to adjust Press the [SRC] button. 4 Adjust the Audio setup item Turn the [VOL] knob. Adjustment Item Volume offset Loudness Display "V-OF" "LOUD" Range ­8 -- ±0 ON/OFF 2 Enter Audio Control mode Press the [VOL] knob. 3 Select the Audio item to adjust Press the [VOL] knob. Each time you press the knob, the item to be adjusted alternates between the items shown in the table below. · Volume offset: Sets each source's volume as a difference from the basic volume. · Loudness: Compensates for low and high tones during low volume. When Loudness is ON, "LOUD" indicator is ON. 5 Exit Audio Setup mode Press the [VOL] knob for at least 1 second. 8| English Speaker Setting Fine-tuning so that the System Q value is optimal when setting the speaker type. Clock Display Press the [CLK] button. · If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. · If the fuse blows, first make sure the wires aren't touching to cause a short circuit, then replace the old fuse with one with the same rating. · Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. · Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. · When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. · After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. · Mount the unit so that the mounting angle is 30° or less. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. Installation Procedure 1. [. . . ] After checking for short circuits in the wires, replace the fuse with one with the same rating. There's a source you can't switch. If there's no media in this unit, you can't switch to each source. The memory is erased when the ignition is turned OFF. [. . . ]