User manual KENWOOD KDC-C661

[. . . ] In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. KENWOOD CORPORATION 2967-3, ISHIKAWA-CHO, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0. 21 CFR 1040. Location : Bottom Panel Accessories/ Installation Procedure 38 Connecting Wires to Terminals Installation Removing the Unit Troubleshooting Guide Specifications 39 40 42 43 46 FCC WARNING This equipment may generate or use radio frequency energy. [. . . ] Refer to 'Notes on Multi-function Key System' (page 10). 2 Start Scan Play Press the [2] ("SCAN") button. "Scan ON" is displayed. 3 Release it when the song you want to listen to is played Press the [2] button. 24 | English Function of MP3/WMA Text/Title Scroll Scrolling the displayed CD text, MP3/WMA text, or MD title. Press the [SCRL] button. Folder Select Quickly selecting the folder you want to listen to. 1 Select the key function section Press the [NEXT] button. Repeatedly press the button until "FSEL" is displayed above the [5] button. Refer to 'Notes on Multi-function Key System' (page 10). Function of disc changers with remote DNPP (Disc Name Preset Play) Selecting the CD displayed in the DNPS of the CDs set in the Disc changer. 2 Enter Folder Select mode Press the [5] ("FSEL") button. During Select mode the folder information is displayed as shown below. Folder name display Displays the current folder name. 1 Enter DNPP mode Press the [DNPP] button on the remote. When "DNPP" is displayed the DNPS display in order. Forward / Reverse display Press the [DISC­] or [DISC+] button. 2 When the disc you want is displayed 3 Select the folder level Press the [FM] or [AM] button. With the [FM] button you move 1 level down and with the [AM] button 1 level up. Selecting a folder in the same level Press the [4] or [¢] button. · If there is no signal in the input Channel, "NO CH" appears. · If you cannot receive any signal in the input Channel due to a bad condition on radio wave or another problem, "Acquiring Signal" appears. 1 Select the preset band Press the [FM] button. 2 Select the key function section Press the [NEXT] button. Repeatedly press the button until the function item is not displayed above the [2] -- [5] button. Refer to 'Notes on Multi-function Key System' (page 10). 3 Call up the channel Press the desired [1] -- [6] button. Selecting the Preset Band Press the [FM] button. Each time the button is pressed the preset band switches between the SR1, SR2, SR3 and SR4. English | 27 SIRIUS tuner control features Channel Scan Every receivable Channel is checked for 10 seconds. 1 Start Channel Scan Press the [AUTO] button for at least 1 second. The channel number display blinks. 2 Release it when the song you want to listen to is received Press the [AUTO] button for at least 1 second. Text Scroll for SIRIUS tuner source Scrolls the displayed channel name and other items. Press the [SCRL] button. 28 | English HD Radio control features SRC MENU AM FM 4 ¢ ST indicator Preset station number Band display Frequency display Tuning Selecting the station. · The HD Radio cannot be selected as a dual zone source. 1 Select HD Radio source Press the [SRC] button. Select the "HD Radio" display. 2 Select the HF band Press the [FM] button. Each time the [FM] button is pressed it switches between the HF1, HF2, and HF3 bands. Select the HA band Press the [AM] button. 3 Tune up or down band Press the [4] or [¢] button. · When you connect an HD Radio, Tuner features of the unit are disabled and switched to HD Radio tuner features. A portion of the setting methods including the Tuning Mode will change. [. . . ] HD Radio tuner is connected to KCA-S210A or other units. Connect the HD Radio tuner directly to the control unit. If the following situations, consult your nearest service center: Even though the disc changer is connected, the Disc Changer source is not ON, with "AUX EXT" showing in the display during the Changer Mode. ?? 44 | English The messages shown below display your systems condition. EJECT: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. [. . . ]