User manual KENWOOD KDC-MP528 Instruction Manual

[. . . ] CD-RECEIVER KDC-X589 KDC-MP5028 KDC-MP528 INSTRUCTION MANUAL Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver. For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product. Model KDC-X589, KDC-MP5028, KDC-MP528 Serial number © B64-2975-00/00 (KW) Contents Safety precautions Notes Warning About CDs About AAC, MP3 and WMA General features Power Selecting the Source Volume Attenuator System Q Audio Control Audio Setup Subwoofer Output Speaker Setting Switching Display Station/Disc Naming (SNPS/DNPS) Faceplate Angle Adjustment Theft Deterrent Faceplate TEL Mute 4 5 6 7 8 9 HD Radio control features Tuning 22 23 Menu system Menu System Security Code Touch Sensor Tone Manual Clock Adjustment DSI (Disabled System Indicator) Selectable Illumination Dimmer Switching preout Built-in Amp Setting Dual Zone System Setting B. M. S. [. . . ] Example: When "BEEP" is selected, each time the knob is pushed it switches "BEEP ON" or "BEEP OFF". You can continue by returning to step 2 and setting other items. English | 23 Menu system In Standby mode 2 Do the step 4 through 7 operation, and enter the Security Code. The unit can be used. Security Code Because authorization by the Security Code is required when it's removed from the vehicle, personalizing this unit is by using the Security Code is a help in preventing theft. In Standby mode · The setup Security Code can be done when the <Demonstration mode Setting> (page 29) is set as OFF. · When the Security Code function is activated, the code can't be changed and the function can't be released. Note, the Security Code can be set as the 4 digit number of your choice. Touch Sensor Tone Setting the operation check sound (beep sound) ON/OFF. Display "BEEP ON" "BEEP OFF" Setting Beep is heard. Beep canceled. 1 Enter Standby Press the [SRC] button. Select the "STANDBY" display. 2 Enter Menu mode Press the [MENU] button for at least 1 second. When "MENU" is displayed, "SECURITY" is displayed. In Standby mode Manual Clock Adjustment 1 Select Clock Adjustment mode Push the Control knob to [FM] or [AM]. Select the "CLK ADJ" display. 3 Enter Security Code mode Press the Control knob for at least 1 second. When "ENTER" is displayed, "CODE" is displayed. 2 Enter Clock Adjust mode Press the Control knob for at least 1 second. The clock display blinks. 4 Select the digits to enter Push the Control knob to [4] or [¢]. 5 Select the Security Code numbers Push the Control knob to [FM] or [AM]. 3 Adjust the hours Push the Control knob to [FM] or [AM]. Adjust the minutes Push the Control knob to [4] or [¢]. 6 Repeat steps 4 and 5, and complete the Security Code. 7 Confirm the Security Code Press the Control knob for at least 3 seconds. When "RE-ENTER" is displayed, "CODE" is displayed. 4 Exit Clock adjustment mode Press the [MENU] button. 8 Do the step 4 through 7 operation, and reenter the Security Code. The Security Code function activates. · When the wrong Code is entered in steps 4 through 6, repeat from step 4. In Standby mode DSI (Disabled System Indicator) A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display "DSI ON" "DSI OFF" Setting LED flashes. LED OFF. Press the Reset button and when it's removed from the battery power source 1 Turn the power ON. 24 | English In Standby mode Selectable Illumination Selecting the button illumination color as green or red. Display "KEY RED" "KEY GRN" Setting The illumination color is red. The illumination color is green. Other than Standby mode/ When the Dual Zone System is ON Dual Zone System Setting Setting the Front channel and Rear channel sound in the Dual Zone System. Display "ZONE2 R" "ZONE2 F" Setting Sub source (Auxiliary input source) is to be rear channel. Sub source (Auxiliary input source) is to be front channel. In Standby mode Dimmer Dimming this unit's display automatically when the vehicle light switch is turned ON. [. . . ] HD Radio tuner is connected to KCA-S210A or other units. Connect the HD Radio tuner directly to the control unit. 38 | English The messages shown below display your systems condition. EJECT: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. No disc has been loaded in the disc magazine. [. . . ]