User manual KENWOOD KR-V6040

[. . . ] In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-4155-00 02 MA (T, E2, Q) OC 9809 Remote Control Other Operations Preparation Getting started 2 Before applying the power Units are designed for operation as follows. and Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V only Russia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2 SURR NO: No surround speakers are connected to the receiver. 7 Press the SETUP key to accept the setting. · The receiver enters the speaker volume level adjustment mode. · In steps 3 and 4, indications appear only for the selected channels of the speakers that require adjusting. Continued to next page Preparations Preparing for surround sound Normal playback KRF-V7020/V6020/V5020 (En/T) 14 Preparing for playback 3 Adjust the volume levels for the speakers. Sit in your normal listening position and listen to the test tone. Adjust the volume levels for the speakers until all speakers seem to be equally loud. 1 Use the MULTI CONTROL (TUNING/SKIP) to adjust the volume when the test tone is being output from the speaker channel to be adjusted. Some preparatory steps are needed before starting playback. VIDEO 2/MONITOR ON/STANDBY AUTO Preparations Operations The channel indication blinks while the test tone is being output. SP A L SW The test tone issues from the speakers for 2 seconds at a time in the following sequence: Lch = Cch = Rch = Sch = Lch · If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. ¢ · If the speaker setting selects are changed, the speaker level settings are reset. 2 Press the SETUP key. Lch + 1 dB POWER INPUT SELECTOR SPEAKERS A/B SPEAKERS, MUTE (KR-V6040) Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER and ON/ STANDBY keys. Selecting TAPE/MD · The receiver enters the mode for inputting the distance to the speakers. Select the source name corresponding to the component connected to the MD/TAPE jacks. 1 Press the SOUND key to select the tone mode to be adjusted. BASS: Select (Press TREB: Select (Press SP this to adjust the low frequency range. the SOUND key once. ) this to adjust the high frequency range. the SOUND key twice. ) L R SW Selecting a source using the AUDIO key on the remote control (RC-R0508) 1 2 3 4 "CD" ("CD"*) "TAPE" or "MD" ("TAPE"*) TUNER "PHONO"("PHONO"*) A TREB +4 AUTO MEMO. STEREO ST. TUNED 2 Use the MULTI CONTROL (TUNING/SKIP) to adjust the sound quality. · The bass and treble levels are adjustable from -10 to +10 in 2 step increments. · The adjustment item is displayed for approximately 8 seconds. · If you used the remote control (RC-R0508) to perform the above setting, press the VIDEO key at this point to turn off the remote control's own adjustment mode. In this case, the input source is not switched. Selecting a source using the VIDEO key on the remote control (RC-R0508) 1 "VIDEO1" ("VCR1"*) 2 "VIDEO2" ("VCR2"*) 3 "DVD 6ch" · When selecting an input source by using the remote control (RCR0710), press the desired input selector key. · "VIDEO 2" can be selected as an input source only if the VIDEO 2/ MONITOR setting is "VIDEO 2". 8 * Once setup codes are registered in the remote control (RC-R0508), the input name display changes according to the name of the registered component. [. . . ] ±10 dB (at 100 Hz) TREBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (at 10 kHz) Caution : Read this page carefully to ensure safe operation. KRF-V7020/V6020/V5020 (En/T) VIDEO section VIDEO inputs / outputs VIDEO (composite) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p / 75 27 FM tuner section Tuning frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87. 5 MHz ~ 108 MHz Usable sensitivity (DIN, 75 ) MONO . . . . . . . . . . . . . . . . . . . . [. . . ]