User manual KENWOOD KRC-108S

[. . . ] · Do not touch the liquid crystal fluid if the LCD is damaged or broken due to shock. The liquid crystal fluid may be dangerous to your health or even fatal. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off with soap immediately. 2CAUTION To prevent damage to the machine, take the following precautions: · Make sure to ground the unit to a negative 12V DC power supply. · Do not open the top or bottom covers of the unit. [. . . ] Setting values: - 8 - + 8 Audio Control Setting Adjust various parameters of sound quality. "BL": Adjust the balance level. Setting values: Left 15 - Right 15 --6-- "FD": Adjust the fader level. Setting values: Front 15 - Rear 15 Adjusting Time Adjust the time. 1 When the time is not displayed, first press the CLK button to display the time. ec4/dB (Sound Coordinate) You can recall the best audio setting preset for different types of the music. 2 Press the CLK button for at least two seconds to enter the clock adjustment mode. The time display will blink. 3 · Adjusting the hours Press the BAND button to advance the hours. · Adjusting the minutes Press the ¢ button to advance the minutes, or press the 4 button to make the minutes go back. 1 Press the AUD button to enter the Sound Coordinate mode. 2 Press a preset button (#1-5). The preset settings of the bass and treble tones are recalled. #1: Flat #2: Rock #3: Pops/Top 40 #4: Jazz #5: Easy 4 Press the CLK button to end the clock adjustment mode. 3 Press the AUD button to end the sound coordinate mode. NOTE You can call the following settings with this function; bass center frequency, bass level, bass quality factor, bass extension, treble center frequency, and treble level setting. Clock display Turning clock display On/Off: Each time you press the CLK button, the display switches between the clock and each mode display. --7-- Tuner features English Tuning SRC / PWR OFF 4 BAND / ¢ CRSC You can choose between auto seek tuning of receivable frequencies and manual tuning. 1 Press the SRC (source) button repeatedly to select the tuner mode. "TUuE" is displayed when the tuner mode has been selected. KRC-108S 2 Press the BAND button to select the band. Each time you press the BAND button, the band switches between FM1, FM2, FM3, and AM. 3 Press the AUTO button to switch between auto seek tuning #1~6 AUTO / AME and manual tuning. The AUTO indicator lights up only when auto seek tuning is selected. 4 · Auto Seek Tuning Press the ¢ button Press the 4 button · Manual Tuning Press the ¢ button Press the 4 button to seek higher frequencies. to decrease the frequency by one step. NOTE Band display Frequency Preset station number The STEREO indicator lights up when stereo broadcasts are being received. Station Preset Memory Store the frequency of a station. You can then recall that station with a single touch of a button. indicator AUTO indicator STEREO indicator 1 Select the band/ station that you want to have stored. 2 Press the button (#1-6) that you want to use for the station, for at least two seconds. The button number blinks once in the display to indicate that the data has been stored. Stopping and Ejecting Cassettes: Press the 0 button. The tape stops playing and the cassette ejects. NOTE Remove a cassette from the unit when not listening to it for a while. If you leave it in the unit too long, the tape may stick to the tape head and cause unit malfunction. Fast Forwarding and Rewinding Cassette Tapes Fast Forwarding Tapes: Press the FF button. The tape indicator blinks in the direction of the tape as it is being fast forwarded. If the REW button is pressed, normal tape play will begin. The tape indicator blinks in the direction of the tape as it is being rewound. If the FF button is pressed, normal tape play will begin. T. CALL indicator Tape indicator -- 10 -- Tuner Call Switch automatically to the tuner while you are rewinding or fast forwarding the tape. Turning Tuner Call On/Off: Press the T. CALL button to switch tuner call on and off. The T. CALL indicator lights up when tuner call is turned on. -- 11 -- Accessories External view Number of items Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. [. . . ] Connect the wire correctly, referring to the section on "Connecting Wires to Terminals". Connect the wire correctly, referring to the section on "Connecting Wires to Terminals". Connect the wire correctly, referring to the section on "Connecting Wires to Terminals". Radio reception is poor. The car antenna is not extended. The antenna control wire is not connected. The memory is erased when the ignition is turned off. The battery wire has not been connected to the proper terminal. [. . . ]