User manual KENWOOD KRF-V6100D

[. . . ] Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-4129-00 00 CS MA (E2, T, Q) MC Getting started 2 Before applying the power Units are designed for operation as follows. Caution : Read this page carefully to ensure safe operation. KRF-V6100D (En/E2T) Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. [. . . ] A ON : Sound from the speakers connected to the SPEAKERS A terminals on the rear panel. B ON : Sound from the speakers connected to the SPEAKERS B terminals on the rear panel. A+B ON : Sound from both the speakers connected to the SPEAKERS A and B terminals on the rear panel. Use this setting when listening with headphones. Preparations Operations Other MUTE BASS BOOST SOURCE DIRECT MULTI CONTROL SOUND BALANCE POWER VOLUME UP, DOWN SOUND BASS BOOST S. DIRECT MUTE BALANCE MULTI CONTROL The indicator for the speakers you want to use should be lit. SP. A B Listening to a source component Preparing for playback Some preparatory steps are needed before starting playback. 1Use the input selector (INPUT SELECTOR) to select the source you want to listen to. The input sources change as shown below: Selecting a source using the INPUT SELECTOR knob 1 2 3 4 5 TUNER (frequency display) "CD" "TAPE 1" or "MD" "PHONO" "AUX" Turning on the receiver 1 Turn on the POWER key to ON. 2 Turn on the power to this receiver by pressing ON/ ) key. STANDBY ( Selecting MD/TAPE 1 (Main unit only) Select the source name corresponding to the component connected to the MD/TAPE1 jacks. The initial factory setting is "TAPE 1". To change the source name associated with the MD/TAPE1 jacks to "MD", follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE 1". 2 Hold down the AUTO key for more than 2 seconds. · Copy from "TAPE 2" to "TAPE 1" is not possible. Preparations Operations Other TAPE2 /MONITOR MULTI CONTROL SOUND MULTI CONTROL SOUND TAPE2 /MONITOR Input level adjustment (when using the monitor function) Recording audio Recording a music source 1 Use the input selector (INPUT SELECTOR) to select the source (other than "TAPE 1") you want to record. 3 Start playback, then start recording. If the input level while using the monitor function is too high, adjust the input level as described below. The input level cannot be adjusted when in the source direct playback mode. 2 Press the SOUND key several times until the "INPUT" indication appears. 3 Use the MULTI CONTROL to adjust the input level. Copying tapes SP. A B TAPE 1 = TAPE 2 copying 1 Use the input selector to select "TAPE 1". 2 Start playback on the cassette deck connected to the MD/TAPE1 jacks and start recording on the cassette deck connected to the TAPE2/MONITOR jacks. · To copy tapes using a double cassette deck, refer to the instruction manual of the double cassette deck. TAPE 2/MONI FW INPUT -6 · The adjustment mode is displayed for approximately 8 seconds. · The input level may be adjusted to any one of 2 settings: 0 and -6. (The initial setting is 0. ) 4 Press the SOUND key to return to the input indication. Listening to radio broadcasts KRF-V6100D (En/E2T) Tuning (non-RDS) radio stations Radio stations can be classified into RDS (Radio Data System) stations and other stations. To listen to or store RDS stations in the preset memory, see the section entitled, "Using RDS". Using RDS (Radio Data System) RDS is a system that transmits useful information (in the form of digital data) for FM broadcasts along with the broadcast signal. [. . . ] 200 mV / 2. 2 k PRE OUT (SUBWOOFER) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 V / 2. 2 k Tone control BASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±9 dB (at 100 Hz) TREBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±9 dB (at 10 kHz) [ FM tuner section ] Tuning frequency range U. K. [. . . ]