User manual KENWOOD KRF-V7300D

[. . . ] Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-4942-10 03 MA (K, P, Y, M, X, I) PR 0009 Additional Information Remote Control Operations Preparations Before applying the power Units are designed for operation as follows. Caution : Read this page carefully to ensure safe operation. 2 Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. [. . . ] 3 Use the MULTI CONTROL keys to adjust the input level. SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS The indicator for the speakers you want to use should be lit. SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS The speaker indicator lights. SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS L LFE C S R SW L LFE C S R SW LS RS LS RS VR-506/KRF-V6050D VR-505/517/KRF-V7300D/ V5550D L LFE C S R SW LS RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO STEREO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP · Selecting "6ch INPT" by pressing the INPUT MODE key, whereby "DVD/ 6ch" is the input source will cause SPEAKER A to be selected automatically. On the VR-505/517/KRF-V7300D/V5550D, press the SPEAKER key to switch the speakers on and off. · The adjustment mode is displayed for approximately eight seconds. · The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB. ) 4 Press the SOUND key again to return to the input indication. Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER (and ON/ STANDBY) key(s). Normal playback Listening to a source component VOLUME CONTROL INPUT SELECTOR 2 Start playback from the selected source. 3 Use the VOLUME CONTROL knob (VOLUME keys) to adjust the volume. Selecting VIDEO 2/MONITOR Depending on the component connected to the VIDEO 2/MONITOR jacks, select either the "VIDEO 2" setting or the "MONITOR" setting, as 9 appropriate. 21 Adjusting the sound MULTI CONTROL SOURCE DIRECT SOUND INPUT SELECTOR VOLUME RC-R0511 RC-R0615/R0617 SPEAKERS A/B PHONES (SPEAKER/MUTE) VOLUME CONTROL 1 Use the INPUT SELECTOR knob to select the source you want to listen to. VR-506/KRF-V6050D 1 2 3 4 5 6 7 8 6 7 1 2 3 4 5 "PHONO" "TUNER" "CD/DVD" "TAPE" or "MD" "VIDEO1" if VIDEO2/MONITOR is VIDEO2 "VIDEO2" "DVD/6ch" "AV AUX" else if VIDEO2/MONITOR is MONITOR "DVD/6ch" "AV AUX" SOUND MULTI CONTROL BASS BOOST/ B. BOOST VOLUME MUTE RC-R0511 RC-R0615/R0617 Adjusting the tone You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. 1 Press the SOUND key to select the tone mode to be adjusted. BASS: Select this to adjust the low frequency range. · To copy tapes using a double cassette deck, refer to the instruction manual of the double cassette deck. Listening with headphones 1 (VR-506/KRF-V6050D) Press the SPEAKERS A or B key so that the speaker indicator goes off. (VR-505/517/V5050D/V5550D) Press the SPEAKER key so that the speaker indicator goes off. Make sure the SPEAKERS indicators are turned off. SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS Make sure the SP indicators are turned off. R RS SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS L LFE C S L LFE C S R RS LS LS VR-506/KRF-V6050D VR-505/517/KRF-V7300D/ V5550D MONITOR function (analog sources only) You can connect a cassette deck or graphic equalizer to the VIDEO2/ MONITOR jacks of the receiver. If a graphic equalizer is connected, the MONITOR key should be left in the on position. Alternately, if a cassette deck equipped with a 3-head system is connected to the VIDEO2/ MONITOR jacks, you will be able to monitor the just-recorded signal while making recordings on the cassette deck. By switching the MONITOR key on and off, you can compare the sound of the source signal and the just-recorded signal. For more information, refer to the instruction manual of the connected component. · If you turn off all of the speakers when in surround mode, the surround mode will be canceled as well, resulting in stereo playback. 2 Connect headphones to the PHONES jack. PHONES 3 Use the VOLUME CONTROL knob (VOLUME keys) to adjust the volume. Recording Listening to radio broadcasts The receiver can store up to 40 stations in the memory and recall them by one-touch operation. Recording video 1 Use the INPUT SELECTOR to select the video source (other than "VIDEO1") you want to record. 2 Set the video deck connected to VIDEO 1 to record. · Select the REC MODE to record a digital input source. · Recording may not be normal for some video software. [. . . ] 1 Vp-p / 75 S VIDEO inputs / outputs (KRF-V6050D) S VIDEO (luminance signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p / 75 S VIDEO (chrominance signal) . . . . . . . . . . . . . . . . . . . . . . 0. 286 Vp-p / 75 FM tuner section Tuning frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87. 5 MHz ~ 108 MHz Usable sensitivity (MONO) . . . . . . . . . . . . . . . . [. . . ]