User manual KENWOOD KRF-V8060D

[. . . ] AUDIO VIDEO SURROUND RECEIVER KRF-V8060D VR-6060 INSTRUCTION MANUAL KENWOOD CORPORATION This instruction manual is for some models. Model availability and features (functions) may differ depending on the country and sales area. About the supplied remote control Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). [. . . ] 2 Turn on the power to this receiver by pressing the POWER ON/STANDBY key (for VR-6060) or POWER ON/OFF and ON/STANDBY (for KRF-V8060D) key. SL S SB SR Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO 2, VIDEO 3 or DVD/6CH jacks, make sure that the input mode setting is correct for the type of audio signal to be used. 8 6 Press the SETUP key to exit the SET UP mode. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink to indicate the source signal. Adjust the input level. SP L C SW R LFE AB MUTE CLIP COAXIAL OPTICAL 6CH INPUT AUTO DETECT CINEM ACTIV DSP M ANALOG 96kHzfs Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source to "MD", follow the steps below: Hold down the MD/TAPE key for more than 2 seconds. SL S SB SR 1 Use the Input Selector keys to select the source of which the input level you want to adjust. · You can store a separate input level for each input source. keys or Joystick (2/3) repeatedly until the "INPUT" indication appears. 3 Use the MULTI CONTROL knob or Joystick (5/) to adjust the input level. SP L C SW R LFE AB MUTE CLIP COAXIAL DTS. DOLBY DIGITAL STEREO OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. MATRIX DSP MODE DISCRETE PRO LOGIC LOUDNESS ANALOG 96kHzfs NEO:6 CSII THX Surround EX RDS RTY AUTO MEMO STEREO TUNED · The source indication changes to "MD". · To return to the original indication, repeat the above procedure. Selecting the speaker system Press the A SPEAKERS B key to select the speaker system to be used. A ON B ON : : Sound from the speakers connected to the SPEAKERS A terminals on the rear panel. Sound from the speakers connected to the SPEAKERS B terminals on the rear panel. No sound will be heard from the subwoofer. Sound from both the speakers connected to the SPEAKERS A and B terminals on the rear panel. Use this setting when listening with headphones for stereo sound in all playback modes. The display segments are different depending on the type of input signal. The indicator for the speakers you want to use should be lit. SP L C SW R LFE AB MUTE CLIP COAXIAL OPTICAL 6CH INPUT AUTO DETECT CINEM ACTIV DSP M ANALOG 96kHzfs A+B ON : A+B OFF : SL S SB SR · The adjustment mode is displayed for approximately 8 seconds. · The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB. ) 4 Press the SOUND key again to return to the input indication. SL S SB SR · Selecting "6CH INPUT" by pressing the INPUT MODE key, whereby "DVD/6CH" is the input source will cause SPEAKERS A to be selected automatically. 22 EN Normal playback Listening to a source component VOLUME CONTROL Adjusting the sound SPEAKER EQ ACTIVE EQ A SPEAKERS B TONE MULTI CONTROL Input Selector AV AUX PHONES LOUDNESS MUTE VOLUME CONTROL POWER VOLUME / MUTE ACTIVE EQ SPEAKER EQ VOLUME / Joystick (MULTI CONTROL 5 / , DOWN 2 / UP3) INPUT SELECTOR LOUDNESS TONE BASS BOOST 1 Use the Input Selector and AV AUX keys to select the source you want to listen to. 1 2 3 4 5 6 7 8 9 "DVD/6CH" "CD/DVD" "PHONO" "TUNER" "VIDEO 1" "VIDEO 2" "VIDEO 3" "MD/TAPE" "AV AUX" Selecting a source using each key. Adjusting the TONE You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. 1 Press the TONE key to select the TONE mode. 2 Use the MULTI CONTROL knob or Joystick (5/) to select TONE ON/OFF. SP L C SW R LFE AB MUTE CLIP COAXIAL DTS. [. . . ] ±0. 32 Vp-p / 75 GENERAL Power consumption VR-6060 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 A KRF-V8060D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 W AC outlet SWITCHED VR-6060 . . . . . . . . . . . . . . . . . . . . . (total 150 W, 1. 25 A max. ) KRF-V8060D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]