User manual KENWOOD KRF-X9050D

[. . . ] AUDIO VIDEO SURROUND RECEIVER Preparation Additional Information Remote Control Operations KRF-X9050D INSTRUCTION MANUAL KENWOOD CORPORATION About the supplied remote control Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-4958-00 00 MA (M, Y, T, I, X) 0011 Before applying the power 2 This unit is designed for operation as follows. [. . . ] Make sure the SPEAKERS indicators are turned off. SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS Once-touch low frequency emphasis (bass boost) (Remote control only) You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo modes. · Press the key once to select the maximum (+10dB) low frequency emphasis setting. · This key does not function when the receiver is in the sound quality or ambience effects adjustment mode. L LFE C S R RS LS · If you turn off all of the speakers when in surround mode, the surround mode will be canceled as well, resulting in stereo playback. 2 Connect the headphones to the PHONES jack. PHONES Switching back to the previous setting Press the BASS BOOST key again. · BASS BOOST key is not effective when THX is ON. THX mode (Remote control only) You may use the THX key to switch ON or OFF the THX mode. The initial factory setting for CD/DVD and DVD/6ch selectors is THX ON. Each press switches the mode as follows: 1 "THX ON" 2 "THX OFF" SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS 3 Use the VOLUME CONTROL knob (RECEIVER VOLUME keys) to adjust the volume. L LFE C S R SW LS RS AUTO FM AUTO SOUND DIGITAL AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP · When THX is ON, "THX" indicator lights up. Recording Recording audio (analog sources) MONITOR Recording video 1 Use the INPUT SELECTOR to select the video source (other than "VIDEO1") you want to record. 2 Set the video deck connected to VIDEO 1 to record. · Select the REC MODE to record a digital input source. · Recording may not be normal for some video software. This is due to the copy guard condition. 25 INPUT SELECTOR Recording a music source 1 Use the INPUT SELECTOR knob to select the source (other than "TAPE") you want to record. 2 Set the cassette deck or MD recorder to record. 3 Start playback, then start recording. Recording audio (digital sources) Switch on the REC mode to record a digital input source. Usually use the A-REC (Auto-Record) mode to record audio input sources. When the digital mode changes during recording in the A- REC mode, the audio may be interrupted momentarily. Recording music in A-REC or M-REC mode DIMMER Recording tapes or MD (with MONITOR function) MONITOR = MD/TAPE recording 1 Press the MONITOR key. INPUT SELECTOR 1 Use the INPUT SELECTOR knob to select the source (CD/DVD, DVD/6ch, VIDEO2, or VIDEO3) you want to record. 2 Set the cassette deck or MD recorder to record. 3 Press and hold the DIMMER key for more than 2 seconds to select the A-REC (or M-REC) mode. · The mode changes every 2 seconds as shown below. 1 Rec mode off : 2 A-REC : The digital input record mode is switched off. The digital input signals (DTS, Dolby Digital, or PCM) are identified automatically and converted into stereo signals that are ready for recording. The input signal type at the moment this mode is selected is held throughout this mode. FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. [. . . ] 1. 6 µV (75 )/ 15. 2 dBf (75 kHz DEV. , SINAD 30 dB) 50dB quieting sensitivity STEREO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 µV (75 )/ 40. 2 dBf Total harmonic distortion (1 kHz) MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 5% (65 dBf input) STEREO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 7% (65 dBf input) Signal to noise ratio (1 kHz, 75 kHz DEV. ) MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]