User manual KENWOOD KRF-X9090D

[. . . ] Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-5197-20 02 ID (K, P, T, M, Y, X, E2) 0109 Before applying the power Units are designed for operation as follows. and Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V only Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB. ) 4 Press the SOUND key again to return to the input indication. 18 EN Normal playback Preparing for playback Some preparatory steps are needed before starting playback. Listening to a source component VOLUME CONTROL INPUT SELECTOR POWER ON/STANDBY SPEAKER ON/STANDBY (KRF-X9090D/ V4060D/ V5560D) ON/OFF (VR-605/615) POWER ON/OFF (KRF-X9090D/ V4060D/ V5560D) AUTO INPUT MODE INPUT SELECTOR Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER ON/ STANDBY (for VR-605/615) or POWER ON/OFF and ON/ STANDBY (for KRF-X9090D/V4060D/V5560D) key. INPUT SELECTOR VOLUME 1 Use the INPUT SELECTOR knob or keys to select the source you want to listen to. The input sources change as shown below: Selecting a source using the INPUT SELECTOR knob. VR-605/615/KRF-X9090D/V4060D/V5560D 1 "AUX" 2 "TUNER" 3 "CD/DVD" 4 "TAPE" or "MD" 5 "VIDEO1" 6 "VIDEO2" 7 "DVD" or "DVD/6CH" (for VR-615/KRF-X9090D only) KRF-X9090D (for the U. K. and Europe only) 1 "PHONO" 2 "TUNER" 3 "CD/DVD" 4 "TAPE" or "MD" 5 "VIDEO1" 6 "VIDEO2" 7 "DVD/6CH" Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO2, DVD or DVD/6CH (VR-615/KRF-X9090D only) jacks, make sure that the input mode setting is correct for the type of audio signal to be used. 8 Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source to "MD", follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE". 2 Hold down the AUTO key for more than 2 seconds. · The source indication changes to "MD". · To return to the original indication, repeat procedure 2. Setting the speaker status The speaker indicator lights up. 2 Start playback from the selected source. 1 Rec mode off : The digital input record mode is switched off. 2 A-REC : The digital input signals (DTS, Dolby Digital, or PCM) are identified automatically and converted into stereo signals that are ready for recording. 3 M-REC : The input signal type at the moment this mode is selected is held throughout this mode. For A-REC mode: INPUT SELECTOR Recording a music source 1 Use the INPUT SELECTOR knob to select the source (other than "MD/TAPE") you want to record. 2 Set the MD or TAPE recorder to record. 3 Start playback, then start recording. Recording video For M-REC mode: 1 Use the INPUT SELECTOR to select the video source (other than "VIDEO1") you want to record. 2 Set the video deck connected to VIDEO 1 to record. · Select the REC MODE to record a digital input source. · Recording may not be normal for some video software. This is due to the copy guard condition. < 4 Start playback, then start recording. Recording audio (digital sources) Switch on the REC MODE to record a digital input source. [. . . ] 64 dB Frequency response . . . . . . . . . . . . . . . . . . . (30 Hz ~ 15 kHz), +0. 5 dB, ­3. 0 dB AM tuner section Tuning frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531 kHz ~ 1, 602 kHz Usable sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 µV / (600 µV/m) Signal to noise ratio (30% mod. [. . . ]