User manual KENWOOD LSF-1010

[. . . ] LSF-1010 SPEAKER SYSTEM INSTRUCTION MANUAL KENWOOD CORPORATION B61-1040-00 EN 2 Introduction LSF-1010 (EN) Before applying power Caution : Read this section carefully to ensure safe operation. Units are designed for operation as follows. Safety precautions Caution : Read this section carefully to ensure safe operation. Europe and U. K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V only FRANÇAIS WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN DEUTSCH CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NEDERLANDS THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED "DANGEROUS VOLTAGE" WITHIN THE PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS. [. . . ] · If the bass volume at the room location at which you normally listen seems unnaturally low, possibly as a result of the room acoustics or the positioning of the subwoofer. Important Operating Notes LSF-1010 (EN) 15 Satellite Speakers 1. The satellite speakers have a nominal impedance of 6 ohms. To ensure safe and efficient speaker operation, be sure that your amplifier or receiver is able to work with 6-ohm speakers. The speaker system's power capacity is indicated in the specifications. Do not operate speakers at power levels above this limit. Doing so may result in damage to the speakers. FRANÇAIS Subwoofer DEUTSCH 1. If supplying a high-level signal, do not over-boost the bass at the amplifier or receiver side. (Avoid excessive use of the amp's bass control and other loudness adjusters. ) 2. Turn the subwoofer volume to its minimum level when making major changes to the sound input (for example, when first switching on the amplifier or when first dropping the needle onto a record). NEDERLANDS ITALIANO ESPAÑOL 16 Adjusting the Satellite Speaker Position LSF-1010 (EN) You can adjust the position of the speaker by changing the height and angle of the arm. 2. Loosen the two screws. Use a coin to turn each screw. Screw · Once you have loosened both screws you will be able to move the arm up and down, or to remove it entirely. FRANÇAIS Use a coin to turn the screws (one screw on each side). Adjusting the Arm Height DEUTSCH Adjusting the arm height Adjusting the arm angle Move the arm up or down to raise or lower the speaker. Getting Ready to Adjust Loosen the two arm screws holding the arm in place (one screw on each side of the arm), so that you can move the arm up and down. 1. Loosen the two arm screws as described above, so that the arm can move up and down. Raise or lower the arm to the desired height, then retighten the two screws. NEDERLANDS 1. Remove the screw cap covering each arm screw. To remove each cap, grasp it at the circumference and peel it off. Screw caps ITALIANO Move arm up or down to desired position. Use a coin to retighten the screws. ESPAÑOL To replace the cap, place it over the screw head and lightly press it along the circumference. 3. Replace the screw caps. You may now want to readjust the angle of the speaker on the arm. You can do this by loosening the screw holding the speaker to the arm, repositioning the screw, and then retightening it. See "Adjusting the Speaker Angle, " on page 8. Adjusting the Satellite Speaker Position LSF-1010 (EN) 17 Adjusting the Arm Angle You can set the arm to any of five different angles by adjusting the angle of the arm holders. 2. Set the arm holders to the desired angle. 1 Take one of the arm holders, rotate it any of the angles A to E indicated at left, and place it back into the opening such that the corners of the arm holder match the ridges on the opening. · Please do not set the arm holders to any angle other than A to E. The speaker may not be stable (and is likely to tip over) if mounted at an angle outside of this range. 2 Loosely fasten the holder in place with the arm screw. · Don't tighten the screw all the way. Tighten only enough so that the arm holder stays in position at the selected angle. [. . . ] 200 Hz to 20, 000 Hz Dimensions (*1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Width : 114 mm (4-1/2 ") Height : 280 mm (11 ") Depth : 130 mm (5-1/8 ") Net Weight (*2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650 g (1. 4 lb) / piece Subwoofer System . . . . . . . . . . . . . . . . . . . . . . . . . . . Subwoofer system with built-in amplifier (Magnetically shielded) [Audio section] Rated Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]