User manual KENWOOD LZ-6500W

[. . . ] · Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. · Do not subject the monitor unit to excessive shock, as it is a piece of precision equipment. · When replacing a fuse, only use a new one with the prescribed rating. [. . . ] "BLK": Adjusts the black level. "DIM": Adjusts the dimmer when it gets dark. Press or button to adjust each item. ENTER 4 5 Select "RETURN" and press to end the Menu mode. Also, the monitor exits from Menu mode by no opeation for 10 seconds. VOICE 4 English Setup MENU 1 2 Press MENU button. ENTER Select "SETUP", and press VOICE button. 3 Press or button to select the adjusting item. "NAV": Setup input and switch method of the navigation picture. Item "RGB"* "AV-IN" "OFF" Setting When Kenwood navigation system is connected by the dedicated cable. When connected to AV-IN terminal be composite signal cable. It doesn't switch the navigation picture. *Default setting If you set to "OFF" while the audio source is set to "NAV", the audio source would switch to "NORMAL". "AV-IN": Setup switch method of the picture input to AVIN terminal. Item "VD"* "CAM" "OFF" Setting Switched by the operation of the video source. Switched automatically when video signal is input to AV-IN terminal. It doesn't switch the picture input to AV-IN terminal. *Default setting You cannot set "AV-IN" when "NAV" is set to "AV-IN". If you set to "OFF" while the audio source is set to "AV-IN", the audio source would switch to "NORMAL". "BEEP": Setup the beep sound ON/OFF. Item "ON" "OFF"* Setting Beep is heard. Beep is canceled. *Default setting 4 5 Press or button to select each item. ENTER Select "RETURN" and press to end the Menu mode. Using screws shorter than those supplied may cause the unit to come looks from · If your car's ignition does not come with an ACC position, connect the ignition cables to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source that receives a constant voltage supply, as with battery cables, the battery may die. · If the fuse blows, first make sure that the cables have not caused a short circuit, then replace the old fuse with one with the same rating. · Do not let unconnected cables or terminals touch metal on the car or anything else conducting electricity. To prevent short circuits do not remove the caps from unused terminals or from the ends of the unconnected cables. · After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. · Insulate unconnected cables with vinyl tape or other similar material. · Thoroughly wipe away oil and other dirt from the installation surface. Please avoid installation on uneven surfaces. 6 English Connection Monitor Unit AV input Audio input (MONO) AV cable (Commercially available) Navigation Unit Visual input Bundle cables with the clamper (Accessory A) Cable accompanying the Navigation System When you connect the Mute Cable to the Navigation System, the voice of the Navigation guide will interrupt. Mute cable (Brown) NAVI MUTE Car fuse box (Main fuse) Ignition key switch Fuse (2A) ACC ACC Connect TEL mute cable of the navigation system. Ignition cable (Red) +12V 2CAUTION +12V For the sake of safety, be sure to connect the parking sensor. PRK SW Battery Ground cable (Black) To car crassic Parking sensor cable (Green) English 7 Installation English Installation for Monitor Unit Installation location and cleaning Select for installation a location where the stand can be placed completely horizontal or where the front edge of the support (petal-shaped part) can be attached horizontally as shown in Figure A. [. . . ] · For safety reasons no video picture are displayed while the vehicle is moving. Engaging the parking brake will cause picture to be displayed. · After checking for short circuits in the cables, replace the fuse with one having the same rating. · Connect the same cable to the ignition as the battery cable. The screen is dark. [. . . ]