User manual KENWOOD MDX-G1

[. . . ] MDX-G1 MINIDISC PERSONAL STEREO SYSTEM INSTRUCTION MANUAL B60-5053-00 00 MA (M) 0102 Before applying power Caution : Read this page carefully to ensure safe operation. Units are designed for operation as follows. AC 120 V only Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V only For the United Kingdom China and Russia . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Recording starts after returning to the beginning of the current track. To stop recording in the middle : Press the 7STOP key. ÷ Be careful not to switch the power off or apply shock or vibrations to the system while "MD WRITING"is displayed. ÷ Once high-speed recording is completed, it is not permitted to record the same CD by high-speed recording within 74 minutes after the start of previous high-speed recording. In case this restriction is applied, the display shows the time until the next high-speed recording becomes possible. HIGH-SPEED TRACK NO. BASS MHz Time until re-recording is available It is also prohibited to continue high-speed of more than 81 tracks within 74 minutes. ÷ If you want to record the same CD again in less than 74 minutes, set "REC SPEED" to "CD=MD NORM" and perform the MD O. T. E. recording (pages 16 to 17). 30 EN Recording onto MD Desired music source can be recorded onto MDs. & STOP MD REC 5 Play the recording source. Application section To stop recording : Press the &STOP key. To let recording pause : AUX MD REC BEST HITS MENU SET TUNING MODE SOUND VOLUME/MULTI CONTROL Press the MD ^ key during recording. Press the MD ^ or MD REC key to resume recording from the pause. Recording 4/ TUNING m STOP TUNING/¢ TUNER FM/AM CD MD In case a message is displayed and recording will not start : See "Display message list" (pages 59). PUSH OPEN 4 TUNER FM /AM ¢ CD ^ MD ^ Main unit only Tips for recording CD onto MD When the MD recorder is in record-pause mode, recording starts automatically at the same time as the playback of CD starts. (Sync recording) 1 Insert a recordable MD. 2 Select the music source to be recorded. CD AUX : Press the CD ^ key. If a CD has already been loaded in advance, it starts playing automatically. Press the &STOP key to stop it. (1) (2) (3) (4) Put the CD player in play-pause mode. Press the 4 or ¢ key to select the CD track to be recorded. Press the MD REC key to put the MD recorder in record-pause mode. Press the CD ^ key to start playing the CD. 3 Press the MD REC key. The unit enters record-pause mode. Display in MD record-pause mode CD TRACK NO. BASS MHz 4 When the recording source is ready for playback, press the MD REC key again. ÷ Be careful not to switch the power off or apply shock or vibrations to the system while "MD WRITING" is displayed. ÷ The MD cannot be inserted or ejected while in STANDBY mode (page 63). Forcing an MD to be inserted or ejected may result in damage. ÷ When the CD output is recorded onto an MD, the digital signal is recorded automatically. When the radio or AUX output is recorded onto an MD, the analog signal is selected automatically. ÷ When recording with high volume, sound skip may occur during MD playback. To avoid this problem, reduce the volume during recording. Continued on next page \ 31 EN Recording onto MD (continued) With regards to track numbers at the time of recording MD track numbers are used to search the beginning of a track or programming tracks. Recording CD tracks onto MD in desired sequence The tracks in a CD can be recorded by rearranging them in the desired sequence when the recording speed is normal (CD=MD NORM). Note that this function is not available when the recording speed is high (CD=MD HIGH). ÷ In MD recording from the radio, AUX or CD source, track numbers are assigned automatically in the following cases. [. . . ] Unmeasurable limit General Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W : 386 mm(16-1/8") H : 146 mm (5-3/4") D : 189 mm (7-7/16") Weight (net) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. 6 kg (12. 3lb) ÷ KENWOOD follows a policy of continuous advancements in development. For reason specifications may be changed without notice. [. . . ]