User manual KENWOOD TH-D72

[. . . ] TH-D72A/ TH-D72E 144/440 MHz FM DUAL BANDER/ 144/430 MHz FM DUAL BANDER INSTRUCTION MANUAL 144/440 MHz FM DOUBLE BANDE/ 144/430 MHz FM DOUBLE BANDE MODE D'EMPLOI DOBLE BANDA DE 144/440 MHz EN FM/ DOBLE BANDA DE 144/430 MHz EN FM MANUAL DE INSTRUCCIONES Only basic operations are explained in this instruction manual. For a detailed explanation on the operations, refer to the PDF file supplied on the CD-ROM. Seules les fonctions de base sont expliquées dans ce mode d'emploi. Pour le détail sur les autres opérations, reportez-vous au fichier PDF à votre disposition sur le CD-ROM. [. . . ] Press [F], [MARK] to turn the internal GPS function ON or OFF. [TNC] (2) Press [TNC] to turn the built-in TNC ON and the APRS (or NAVITRA) mode ON. · · · Each time you press [TNC], the mode cycles through the following: APRS (or NAVITRA) mode ON PACKET mode ON TNC OFF. When the built-in TNC turns on, "OPENING TNC" appears on the display. During "OPENING TNC" appears on the display, the mode cannot be changed. Press [F], [TNC] to turn the Tracking Log function ON or OFF. [POS] (3) Press [POS] to display your "My position" (using the internal GPS) or to enter the Position registration mode (not using the internal GPS) <APRS>. Press [F], [POS] to enter the My Weather mode <APRS>. [MSG] (4) Press [MSG] to display the Message list. Press [F], [MSG] to enter the New Message input mode <APRS>. 10 [LIST] (5) Press [LIST] to display the Station list. Press [F], [LIST] to display the DX Cluster list <APRS>. [BCON] (6) Press [BCON] to enter the Beacon Transmit mode (When TX Beacon method is Manual) or turn the Beacon function ON or OFF (When TX Beacon method is other than Manual) <APRS>. Press [F], [BCON] to enter the Quick Beacon mode <APRS>. [REV] (7) Press [REV] to turn the Reverse function ON or OFF. Press [REV] (1s) to turn the Automatic Simplex Checker ON. Press [F], [REV] to enter the Voice Alert function setup mode <APRS>. [TONE] (8) Press [TONE] to turn the Tone function ON. · · Each time you press [TONE], the function cycles through the following: Tone ON CTCSS ON DCS ON Cross Tone ON OFF. Additionally, when APRS is ON and Voice Alert is configured, Voice Alert ON is added to the above cycle. Press [F], [TONE] to enter the Tone frequency, CTCSS frequency, DCS code, or Cross Tone setup mode. Press [F], [TONE] (1s) to start the Tone frequency ID, CTCSS frequency ID, or DCS code ID scan. [PF] (9) Press [PF] to activate its programmed function. The default function is "Weather Channel" (TH-D72A)/ "Memory Name < > Frequency" (TH-D72E). [MHz] ( ) Press [MHz] to enter the MHz mode. Press [F], [MHz] to enter Offset Direction setup mode. · Each time you press [F], [MHz], the offset direction cycles through the following: plus (+) direction minus (­) direction ­7. 6 MHz (TH-D72E only) OFF. [DUAL] (0) Press [DUAL] to switch the Single band mode and Dual band mode. Press [F], [DUAL] to turn the Full duplex function ON or OFF. [. . . ] Packet operation results in no connects with other stations. 1 The squelch is open. 2 You did not select the 2 Use HBAUD command same transfer rate as to select the appropriate the target station. transfer rate. When transmitting in full duplex mode, another signal is being received at the same time. You are receiving the transmitted signal of your station. Change your settings to a transmit frequency that does not receive the signal, or change the receive frequency. Example frequency setting : Transmit frequency of 146. 000 MHz and receive frequency of 439. 600 MHz You cannot transmit any APRS data. 1 Beacon is OFF. 2 The squelch is open. 1 Press [BCON] to switch Beacon ON. [. . . ]