User manual KENWOOD TM-G707E

[. . . ] INSTRUCTION MANUAL 144/440 MHz FM DUAL BANDER TM-G707A TM-G707A TM-G707E 144/430 MHz FM DUAL BANDER 144/430 MHz FM DUAL BANDER KENWOOD CORPORATION © B62-1509-00 (K, E, M) 09 08 07 06 05 04 03 02 01 00 THANK YOU! We are grateful you decided to purchase this KENWOOD FM transceiver. This series of mobile transceivers was developed to satisfy the requirement for a compact rig that’s simple to operate yet contains numerous sophisticated features. The dual band operation will be appreciated by hams who want access to VHF and UHF bands with a transceiver smaller than some single banders. KENWOOD believes that the compact size, coupled with the reasonable cost, will meet your satisfaction. FEATURES This transceiver has the following main features. [. . . ] You may want to dedicate the Call channel as an emergency channel within your group. In this case, the Call/VFO scan {page 43} will be useful. The default frequency stored in the Call channel is shown below: ■ Changing Call Channel Contents 1 Select the desired band. 2 Select the desired frequency and related data (Tone, CTCSS, etc. ). • When you program the Call channel as an odd-split channel, select a receive frequency. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 3 Press [F], [CALL]. • The selected frequency and related data are stored in the Call channel. • When programming as an odd-split channel, press [F], [CALL] (1 s) instead. “–” and “+” appear. Version U. S. A. / Canada Europe/ General VHF 144. 000 MHz 144. 000 MHz UHF 440. 000 MHz 430. 000 MHz To use as an odd-split channel, proceed to the next step. 4 Turn the Tuning control, or press Mic [UP]/ [DWN], to select the desired transmit frequency. 5 Press [CALL] again. • The selected transmit frequency is stored in the Call channel, and the previous mode is restored. Note: ◆ Transmit Offset status and Reverse status are not stored in an The contents of the Call channel cannot be deleted; however, you can overwrite old data with new data as described in the following section. ■ Recalling the Call Channel 1 Select the desired band. 2 Press [CALL] to recall the Call channel. • “C” appears. odd-split Call channel. ◆ To store data other than frequencies, select the data in step 2 not step 4. • To restore the previous mode, press [CALL] again. 31 MEMORY ➡ VFO TRANSFERS 1 2 3 4 5 6 7 8 9 10 ◆ CHANNEL DISPLAY FUNCTION When this function is switched ON, the transceiver displays only a memory channel number instead of a frequency. Press [LOW]+[ ] to switch this function ON (or OFF). 2 Transferring the contents of a memory channel or the Call channel to the VFO can be useful if you want to search for other stations or a clear frequency, near the selected memory channel or Call channel frequency. 1 Recall the desired memory channel or the Call channel. 2 Press [F], [VFO]. • The entire contents of the memory channel or the Call channel are copied to the VFO. VFO mode is selected after the transfer is completed. Note: 1 A transmit frequency from an odd-split memory channel or odd-split Call channel is not transferred to the VFO. To transfer a transmit 11 frequency, press [REV], then press [F], [VFO]. ◆ Lockout status and memory names are not copied from a memory 12 channel to the VFO. When in Channel Display mode, you cannot use the following functions: • VFO Select • Programmable Memory Recall • Memory Channel Store • Memory ➞ VFO Transfer • Freq. Step Size Change • Easy Operation Select • Programmable Memory Reset Note: ◆ • MHz Function Select • Programmable Memory Store • Call Channel Store • Memory Channel Clear • VFO Scan • Partial/ Full reset 13 14 15 16 17 18 19 20 21 22 32 You cannot switch this function ON if you have stored frequencies in no memory channels. ◆ When in Channel Display mode, you may want to recall only memory channels of the desired band. Before pressing [LOW]+[ ], select “ONE” in Menu No. 4 (MR), then select the desired band. INITIALIZING MEMORY If your transceiver seems to be malfunctioning, initializing the transceiver may resolve the problem. In addition, doing Full Reset is a quick way to clear all memory channels; however, you then need to re-program memory channels after initialization. Note: While using the Channel Display or All Lock function, you cannot ■ Partial Reset (VFO) Use to initialize all settings except the memory channels, the Call channel, the PM channels, and Memory Channel Lockout. [. . . ] 6 VS-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Keypad Direct Entry Frequency . . . . . . . . . . . . . . . . . . . . . . . . 54 Memory Channel Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Tone Frequency Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]