User manual KENWOOD TM-V71A

[. . . ] A maximum of 280 memory channels are available, 140 each for VHF and UHF. Up to 180 memory channels can be assigned desired names. “Visual Scan” graphically and simultaneously shows the conditions of up to 147 frequency channels. The Dual Band RX feature allows two frequencies to be simultaneously received. [. . . ] Solution: In two PM channels, store the same operating data such as frequency, offset, DTSS code, etc. , and store different settings for the Display Dimmer and Beep functions. Then you can quickly recall the best settings for day or night operating. Situation 3: You cannot figure out how you can make the transceiver exit the current mode. Solution: Simply recall PM channel 1 that contains an exact copy of the transceiver default environment. You will not lose the contents of any memory channels. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 37 STORING DATA IN PM CHANNELS 1 2 3 4 5 6 7 8 9 10 11 12 13 VOL SQL CALL RECALLING PM CHANNELS 1 Press [PM]. • The PM channel numbers appear. CALL 1 Confirm that the following conditions have been satisfied: • • • Both bands are in the receive mode. Microphone Control is OFF. 2 Select the desired band. 3 Select the desired frequency and related data (Tone, CTCSS, DTSS, etc. ) using VFO mode. 4 If required, select another band, then select the desired frequency and related data. 5 Press [F], [PM]. • The PM channel numbers appear and blink. VOL SQL 2 Press [1] to [4] corresponding to the desired PM channel. • • • The contents of the selected channel are recalled. The selected channel number appears at the left bottom of the display. To exit PM Recall mode, press [PM], [VFO]. 2 Note: You cannot recall a PM memory channel while transmitting. 14 1 15 16 17 18 19 20 21 6 Press [1] to [4] corresponding to the desired PM channel. • The selected frequency and related data are stored in the PM channel. 38 AUTO PM CHANNEL STORING After you recalled a PM channel, this function automatically overwrites the current PM channel with the present operating environment when: • • • You recall another PM channel. 2 Turn the Tuning control, or press Mic [UP]/[DWN], to select the operating frequency. • This frequency will also be used as the center frequency. 3 Press [F], [VISUAL] to start Visual Scan. Press [PAUSE] again to resume. ◆ If you start Visual Scan in Memory Recall mode, the memory channel frequencies will be scanned. If you start Visual Scan after recalling the Call channel, the call channel frequency will be used as the center frequency. Starting Visual Scan switches Automatic Band Change OFF. If you start Visual Scan in one of the following conditions, you cannot receive in the current operating frequency. To use this frequency, press [PAUSE] to halt Scan. • Memory Recall or Call Channel mode • The VHF band, VFO mode, and a frequency in the range 118 MHz to 136 MHz were selected. Depending on conditions, Visual Scan and the conventional S-meter may indicate different signal strength levels. 4 To change the operating frequency, turn the Tuning control or press Mic [UP]/[DWN]. • • • The displayed frequency changes and the cursor moves. Press [SET] to use the changed operating frequency as the center frequency. Press [RESET] to restore the previous operating frequency. 5 To quit Visual Scan, press [OFF]. 42 SCAN RESUME METHODS Before using Scans other than Visual Scan, it’s necessary to decide under what condition you want your transceiver to continue scanning after detecting and stopping for a signal. You can choose Time-Operated mode or Carrier-Operated mode. [. . . ] 6 VS-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Keypad Direct Entry Frequency . . . . . . . . . . . . . . . . . . . . . . . . 74 Memory Channel Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Tone Frequency Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]