User manual KENWOOD VR-715

[. . . ] AUDIO VIDEO SURROUND RECEIVER VR-705 VR-715 KRF-V5070D KRF-V4070D KRF-V5570D INSTRUCTION MANUAL KENWOOD CORPORATION This instruction manual is for some models. Model availability and features (functions) may differ depending on the country and sales area. About the supplied remote control Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). [. . . ] The selection of AUTO/MANUAL TEST TONE is done by the MULTI CONTROL knob or keys. 1 AUTO 2 MANUAL 2 Press the SETUP key again to select either AUTO or MANUAL. Use the MULTI CONTROL knob or keys to adjust the volume level of the test tone output from the speaker channel to be adjusted. For AUTO selection, the test tone is heard from the speakers in the following sequence for 2 seconds each: · The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. 7 Press the SETUP key to exit the SETUP mode. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink to indicate the source signal. Adjust the input level. 1 Use the INPUT SELECTOR knob to select the source of which the input level you want to adjust. · You can store a separate input level for each input source. 2 Press the SOUND key repeatedly until the "INPUT" indication appears. 3 Use the MULTI CONTROL knob or keys to adjust the input level. · If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. § · If any of the speaker is set as OFF during SP SETUP, the TEST TONE adjustment for the speaker will be skipped. · The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB. ) 4 Press the SOUND key again to return to the input indication. 17 EN Normal playback Preparing for playback Some preparatory steps are needed before starting playback. Listening to a source component VOLUME CONTROL INPUT SELECTOR POWER ON/STANDBY SPEAKERS ON/STANDBY (KRF-V5070D/ V4070D/ V5570D) ON/OFF (VR-705/715) POWER ON/OFF (KRF-V5070D/ V4070D/ V5570D) AUTO INPUT SELECTOR Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER ON/ STANDBY (for VR-705/715) or POWER ON/OFF and ON/ STANDBY (for KRF-V5070D/V4070D/V5570D) key. Input Selector VOLUME 1 Use the INPUT SELECTOR knob or keys to select the source Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO2, DVD or DVD/6CH (VR-715/KRF-V5070D only) jacks, make sure that the input mode setting is correct for the type of audio signal to be used. 8 you want to listen to. The input sources change as shown below: 1 2 3 4 5 6 7 "AUX" "TUNER" "CD/DVD" "TAPE" or "MD" "VIDEO1" "VIDEO2" "DVD" or "DVD/6CH" (for VR-715/KRF-V5070D only) Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source to "MD", follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE". 2 Hold down the AUTO key for more than 2 seconds. · The source indication changes to "MD". · To return to the original indication, repeat procedure 2. 2 Start playback from the selected source. 3 Use the VOLUME CONTROL knob or VOLUME keys to adjust the volume. Setting the speaker status The speaker indicator lights up. Press the SPEAKERS ON/OFF key to switch the speaker on or off. 18 EN Normal playback Adjusting the sound Adjusting the LOUDNESS mode (remote control only) SPEAKERS ON/OFF ACTIVE EQ VOLUME CONTROL You can adjust the Loudness function which controls the low volume settings to maintain the music's richness. The adjustment can be made when the receiver is in the PCM stereo and analog stereo mode. Press the LOUDNESS key to turn the LOUDNESS setting ON. To cancel Press the LOUDNESS key again so that the "LOUDNESS" indicator goes off. PHONES MULTI CONTROL MUTE Muting the sound The MUTE key lets you mute the sound of the speakers. [. . . ] ±10 dB (at 10 kHz) Loudness control VOLUME at -30dB level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8 dB (at 100 Hz) AM tuner section Tuning frequency range 10 kHz step (VR-705/715) . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 kHz ~ 1, 700 kHz 10 kHz step (KRF-V5070D/V4070D/V5570D) . 530 kHz ~ 1, 610 kHz 9 kHz step (KRF-V5070D/V4070D/V5570D) . . . [. . . ]