User manual KENWOOD VR-716

[. . . ] AUDIO VIDEO SURROUND RECEIVER VR-716 INSTRUCTION MANUAL KENWOOD CORPORATION About the supplied remote control Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-5335-00 00 ID (K, P) FE 0211 Before applying the power Units are designed for operation as follows. [. . . ] · The allowable setting range is 1 to 30 feet (0. 3m to 9. 0m), adjustable in 1 foot (0. 3m) increments. 4 Press the SETUP key to accept the settings. 5 Repeat steps 3 and 4 to input the distance for each of the speakers. 6 Setup is complete when the EXIT indication appears. 5Adjust the speaker volume level. From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. 1 Press the SETUP key to begin TEST TONE. The selection of AUTO/MANUAL TEST TONE is done by the MULTI CONTROL knob or Multi % / fi keys. 1 AUTO 2 MANUAL 2 Press the SETUP key again to select either AUTO or MANUAL. Use the MULTI CONTROL knob or Multi % / fi keys to adjust the volume level of the test tone output from the speaker channel to be adjusted. For AUTO selection, the test tone is heard from the speakers in the following sequence for 2 seconds each: · The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. 7 Press the SETUP key to exit the SETUP mode. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink to indicate the source signal. Adjust the input level. 1 Use the INPUT SELECTOR knob to select the source of which the input level you want to adjust. · You can store a separate input level for each input source. 2 Press the SOUND key repeatedly until the "INPUT" indication appears. 3 Use the MULTI CONTROL knob or Multi % / fi keys to adjust the input level. The channel indication blinks while the test tone is being output. · If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. § · If any of the speaker is set as OFF during SP SETUP, the TEST TONE adjustment for the speaker will be skipped. · The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB. ) 4 Press the SOUND key again to return to the input indication. 17 EN Normal playback Preparing for playback Some preparatory steps are needed before starting playback. Listening to a source component VOLUME CONTROL SPEAKERS ON/OFF POWER ON/STANDBY INPUT SELECTOR AUTO INPUT SELECTOR Input Selector Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER ON/ STANDBY key. ¢ + + 4 VOL + Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO 2 or DVD/6CH jacks, make sure that the input mode setting is correct for the type of audio signal to be used. 8 1 Use the INPUT SELECTOR knob or keys to select the source you want to listen to. The input sources change as shown below: 1 2 3 4 5 6 7 "AUX" "TUNER" "CD/DVD" "TAPE" or "MD" "VIDEO1" "VIDEO2" "DVD/6CH" Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source to "MD", follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE". [. . . ] 87. 5 MHz ~ 108. 0 MHz Usable sensitivity (MONO) . . . . . . . . . . . . . . . . . 1. 3 µV (75)/ 13. 2 dBf (75 kHz DEV. , SINAD 30 dB) 50dB quieting sensitivity STEREO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 µV (75)/ 40. 2 dBf Total harmonic distortion (1 kHz) MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 5% (71. 2 dBf input) STEREO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]