User manual KENWOOD VR-804

[. . . ] AUDIO VIDEO SURROUND RECEIVER VR-804 KRF-V4080D KRF-V5580D INSTRUCTION MANUAL KENWOOD CORPORATION This instruction manual is for some models. Model availability and features (functions) may differ depending on the country and sales area. About the supplied remote control Compared to standard remote controls, the remote control supplied with this model has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). [. . . ] · In step 4 and 5, indications appear only for the selected channels of the speakers that require adjusting. 1 Press the SETUP key to begin TEST TONE. · This model enters the speaker volume level adjustment mode. The selection of AUTO/MANUAL TEST TONE is done by the MULTI CONTROL knob or keys. 1 AUTO 2 MANUAL 2 Press the SETUP key again to select either AUTO or MANUAL. Use the MULTI CONTROL knob or keys to adjust the volume level of the test tone output from the speaker channel to be adjusted. For AUTO selection, the test tone is heard from the speakers in the following sequence for 2 seconds each: · The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. 7 Press the SETUP key to exit the SETUP mode. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink to indicate the source signal. Adjust the input level. 1 Use the INPUT SELECTOR knob to select the source of which the input level you want to adjust. · You can store a separate input level for each input source. 2 Press the SOUND key repeatedly until the "INPUT" indication appears. 3 Use the MULTI CONTROL knob or keys to adjust the input level. · If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. § · If any of the speaker is set as OFF during SP SETUP, the TEST TONE adjustment for the speaker will be skipped. · The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB. ) 4 Press the SOUND key again to return to the input indication. 17 EN Normal playback Preparing for playback Some preparatory steps are needed before starting playback. Listening to a source component VOLUME CONTROL INPUT SELECTOR POWER ON/STANDBY SPEAKERSON/STANDBY (KRF-V4080D/ V5580D) ON/OFF (VR-804) POWER ON/OFF (KRF-V4080D/ V5580D) AUTO INPUT SELECTOR Turning on this model 1 Turn on the power to the related components. 2 Turn on the power to this model by pressing POWER ON/ STANDBY (for VR-804) or POWER ON/OFF and ON/ STANDBY (for KRF-V4080D/V5580D) key. Input Selector VOLUME 1 Use the INPUT SELECTOR knob or keys to select the source Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO2, DVD (VR-804/KRF-V5580 only) or DVD/6CH (KRF-V4080D only) jacks, make sure that the input mode setting is correct for the type of audio signal to be used. 8 you want to listen to. The input sources change as shown below: 1 2 3 4 5 6 7 "AUX" "TUNER" "CD/DVD" "TAPE" or "MD" "VIDEO1" "VIDEO2" "DVD" or "DVD/6CH" (for KRF-V4080D only) Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source to "MD", follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE". 2 Hold down the AUTO key for more than 2 seconds. · The source indication changes to "MD". · To return to the original indication, repeat procedure 2. 2 Start playback from the selected source. [. . . ] 550 mV / 1 k PRE OUT (SUBWOOFER) (KRF-V4080D) . . . . . . . . . . . . . 1. 5 V / 2. 2 k Tone control BASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (at 100 Hz) TREBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (at 10 kHz) Loudness control VOLUME at -30dB level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]