User manual KENWOOD XD-A51

[. . . ] 3-1-3 Condition in test mode POWER • • • • • • ON SELECTOR • • • AUX (in case of [INPUT] key) TUNER (in case of [BAND] key) FL , LED • • • • • All the fluorescent display indicators and LEDs light. (The all illuminated state is cleared by pressing any main unit key or remocon key. (1) The muting during mode selection is not controlled in the test mode. (2) The test mode is cancelled when the AC power is turned OFF. [. . . ] 0 MHz ALIGNMENT POINTS ALIGN FOR Adjust VR1 and stop at the point where ED1 (TUNED) goes ON. Test mode of CD player 2-1 Main unit (1) Setting of the test mode While pressing the [PLAY/PAUSE] key, plug the AC power cord into AC outlet. (2) Canceling of the test mode Press the [STOP] key on stop mode or unplug the AC power code from AC wall outlet. Step 1, 2 are in TEST MODE TEST MODE : While pressing the [PALY/PAUSE] key, plug the AC power cord into the AC outlet. Set the senor section of the optical power Press the"PLAY"key meter on the pickup to check that the display is "03". When the diffraction grating is correctly aligned with the RF level of 0. 8Vp-p or more 1 LASER POWER – – (a) 2 FOCUS ERROR BALANCE Test disc Type 4 Press the "PLAY" key. Confirm that the display is”05” FE BALANCE VR1 Optimum eye pattern (d) Note: Type 4disc :SONY YEDS-18 Test Disc or equivalent. ¶ Perform the tangential and focusing offset are focused into one point on the display. The crossing points above and below the center shall also be looked clearly. Test mode of DECK section (1) Setting While pressing the PLAY key(DECK), plug the AC power cord into an AC power outlet. To reduce the risk of electric shock, leakage-current or resistance measurements shall be carried out (exposed parts are acceptably insulated from the supply circuit) before the appliance is returned to the customer. 6 MOTOR-(B) 5 +12V 4 (GND) 3 (GND) 2 1 SOL(-) 15 14 13 12 11 MOTOR(-) (INH A) COM (PLAY B) (CRO B) 10 9 (B PH) (HALF B) 8 7 MOTOR-(A) 6 MOTOR-(B) 5 +12V 4 (GND) 3 (GND) 2 (NH B) 1 SOL(-) R83 +B -B RECORDING LINE SIGNAL LINE GND LINE +B LINE -B LINE MOTOR-(A) MOTOR(-) COM (PLAY A) (CRO A) CN3 CN4 R79 150K 22K R81 110K A-DECK B-DECK RXD-A5/501/501E/501W/551/551E/551W/571S(K) (2/8) RXD-701/701E/701W/A8/751/751E/751W/771S(K) (2/8) The DC voltage is an actual reading measured with a high impedance type voltmeter with a cassette loaded at playback mode. The measurement value may vary depending on the measuring instruments used or on the product. Bias circuit DC voltage is measured while in the record mode. DOLBY and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Noise reduction circuit made under license from Dolby Laboratories Licensing Corporation. 2MHz C36 12P C37 10P 3 D10 6 CAUTION: For continued safety, replace safety critical components only with manufacturer's recommended parts (refer to parts list). For continued protection against risk of fire, replace only with same type and rating fuse(s). To reduce the risk of electric shock, leakage-current or resistance measurements shall be carried out (exposed parts are acceptably insulated from the supply circuit) before the appliance is returned to the customer. 7 ( ) C38 470P R21 1K 5 ( ) R22 1K 4 ( ) R23 1K 2 ( ) R20 1K 11 1 2 3 4 5 6 7 8 12K The DC voltage is an actual reading measured with a high impedance type voltmeter as the AM/FM signal generator is specified to the conditions as shown in the list below. The measurement value may vary depending on the measuring instruments used or on the product. [. . . ] The DC voltage is an actual reading measured with a high impedance type voltmeter. The measurement value may vary depending on the measuring instruments used or on the product. Refer to the voltage dur ing PLAY unless otherwise specified; The value shown in ( ) is the voltage measured at the moment of STOP. And Canada ) 100 watts per channel minimum RMS, both channels driven, at 6 Ω from 40Hz to 14kHz with no more than 0. [. . . ]