User manual KING TECHNOLOGY NEW WATER CYCLER (ENGLISH)

[. . . ] New Water Fresh and Clean ® Easy-Does-It Chlorine Pool-Care System The New Water Cycler and Replacement Cycler Pac ® Instruction Manual Customer Service 800-222-0169 TABLE OF CONTENTS Page No. Introducing New Water Pool Balancing New Water Cyclers Parts List Above Ground Base Installation Above Ground Filter Installation In Ground In-Line Installation In Ground Off-Line Installation Replacing a Cycler Pac Setting Control Dial For Ultimate Performance Cycler Maintenance Replacing o-rings & knobs Winterizing Warranty 3 3 4 5 6 7 8 9-10 11 12 13 14 15 16 2 New Water ® Thank you for choosing New Water. This system will maintain a clean, clear swimming pool while you spend less time on maintenance and more time having fun! ® ® For In Ground Pools For Above Ground Pools New Water Cycler ® The New Water Cycler is on constant watch dispensing chlorine to control bacteria and provide a protective bank of sanitizer for your pool. Pool Balancing Water Balance Guidelines Free Chlorine: pH: Total Alkalinity: Calcium Hardness: Stabilizer: 1. 0 - 3. 0 ppm 7. 2 - 7. 8 60 - 120 ppm 150 - 400 20 - 80 ppm Total Dissolved Solids: <1500 1. Before beginning with any pool care program, you must first balance your pool water. Take a water sample to your local pool professional or use a complete test kit that will test for the following important elements. 4. [. . . ] If reading drops below 1. 0 ppm, shock pool again. Turn control dial to minimum when shocking and NEVER ADD SHOCK IN OR NEAR THE SKIMMER. Reset dial 1/2 setting higher than before and continue to monitor daily until desired chlorine level is achieved. Test Strips Pool and Spa Test Strips 2. For the first week or so, test the water daily for free chlorine. Decrease the number of hours your pump runs per day. Remove the Pac and place open ends down on the equipment pad until dry. Avoid placing on any surface that may be damaged by chemical exposure. Keep out of reach of children and pets. 3. After day one, adjust the dial up by 1/2 increment if the free chlorine reading has dropped or down by 1/2 increment if the reading has risen. Continue this process each day until the reading stabilizes at your desired level between 1. 0- 3. 0 ppm. Remember to adjust dial by 1/2 increments only. Higher than suggested settings could result in over chlorination and/or bleached pool surfaces. Use the handle end of cap tool if the dial is hard to turn. 12 When reading drops to desired ppm, replace Cycler Pac and . . . . . . decrease dial 1/2 increment. Repeat this process until desired chlorine level is maintained. For Ultimate Performance A. With High GPMS Install T-fittings exactly as shown. CYCLER TO POOL 1) Make sure back pressure Is between 3 and 8 psi Higher back pressures result in over chlorination. Lower back pressures result in under chlorination. Adjust eye ball fittings in the return jets to a larger size to decrease back pressure or smaller size to increase back pressure. CHECK VALVE SUCTION FROM POOL/SPA 2) Determine possible high-flow situations that require a special installation such as: A. Pool and spa combination with common equipment. NOTE: Over chlorination or damage to the Cycler or other equipment could result if these special installations are not used in these situations. 3-WAY VALVE CYCLER ® IN-FLOOR VALVE PUMP C. Pool and Spillover Spa Combination POOL WATER LEVEL SUCTION FROM POOL/SPA PUMP CHECK VALVE 3-WAY TO POOL TO SPA CYCLER 13 Cycler Maintenance Replacing the Control Dial O-Rings for Above Ground Cyclers Replacing the Control Dial O-Ring Kit for In Ground Cyclers 1. In the back of the Cycler depress tab at end of locking pin with a pen or screwdriver and pull pin out of dial. 1. Using a needle nose pliers, find the snap ring tail located at approximately the five o'clock position under the control dial. 2. Turn control dial back and forth as you pull it out of the housing. Back o-ring OTHER COPY? SILICONE LUBRICANT COPY COPY COPY COPY 3. [. . . ] Purchaser must present the sales receipt or other documentation verifying proof of purchase. This warranty does not cover defects caused by: Modification, alteration, repair or service of the unit contrary to the accompanying instructions; physical abuse to or misuse of the product or operation or installation in a manner contrary to the accompanying instructions. This warranty also excludes all costs arising from the installation, adjustment, removal or replacement of defective units or parts. This warranty also excludes any and all claims arising out of the chemicals used in the product or their characteristics. [. . . ]