User manual KING TECHNOLOGY POOL FROG IN GROUND MINERAL SYSTEM

[. . . ] Pool FROG In GROUND MINERAL SYSTEM FOR POOLS Patented Mineral Pool Sanitizer ROG OL F VOIR PO THE L RESER ED RA AC MINE BE REPL THS MUST SIX MON OOL Y P EVER ER ONE VER FT HE OR A N WHIC . O R SEAS SHORTE IS ® Instruction Manual Customer Service 800-222-0169 TABLE OF CONTENTS POOL FROG Introduction Swimming Pool Tips Start-up and Operation Replacing POOL FROG Mineral Reservoir Replacing FROG BAM ® ® ® 3 4 5-6 7 8 Replacing POOL FROG Bac Pac Troubleshooting Parts List Replacing Control Dial O-Rings Replacing Cap O-Ring and Knob Winterizing In-line Installation Off-line Installation For Proper Performance Warranty ® 9 10 11 12 12 13 14 15-16 17 18 POOL FROG ® Welcome to easier pool care courtesy of POOL FROG®. With POOL FROG®, your pool water will look and feel better without a lot of work or a lot of chlorine. This system controls bacteria using a combination of minerals and reduced chlorine levels­up to 50%* less. [. . . ] If you are unable to maintain 0. 5 to 1. 0 ppm, first make sure there are chlorine tablets in the tower areas of the POOL FROG® Bac Pac and it is installed properly. If a correction was made, test the water in 24 hours. If still low, turn the dial up one setting and test the water again in 24 hours. Continue raising the setting by one increment each day until the proper reading is achieved. Shock the pool if the reading has been lower than 0. 5 ppm for more than one day. Contact your dealer to have your back pressure tested to ensure it is between 3 & 8 psi. Contact King Technology's Customer Service Department at 800-222-0169. 5. What do I do if I am over chlorinating with the POOL FROG® Bac Pac? 1. If the chlorine reading is over 3. 0 ppm, remove the POOL FROG® Bac Pac from the POOL FROG® Mineral Reservoir and test the water daily until the reading is down to 1. 0 ppm. If the reading has risen, lower the dial one setting again. Continue this process until proper reading is achieved. you may be circulating the water more than is necessary which results in more chlorine than is necessary. Contact King Technology's Customer Service Department at 800-222-0169. 3. If over-chlorinating at the lowest possible setting, consider 2. Reinsert the POOL FROG® Bac decreasing the circulation time. Pac, lower the dial one setting and Depending on your pump size, test the water again in 24 hours. 10 Parts List Models 5400/5430 18 1 2 3 OTHER COPY? SILICONE LUBRICANT 19 4 COPY COPY COPY COPY 9 8 5 6 7 10 11 12 13 15 16 17 14 POOL FROG¤ CYCLER DIAGRAM/PARTS LIST · Model 5400 REF. 1&2 2 3 4 5, 6, 7 6&7 8&9 10 18 19 01-22-9412 01-22-9920 N/A 01-22-9480 01-22-9440 01-22-9450 01-22-9940 01-22-9490 01-22-8870 01-22-9971 Cap w/O-Ring Cap O-Ring Body Pressure Relief Valve Control Dial with O-Ring & Snap Ring Control Dial O-Ring Kit Knob with O-Ring 2" Male Adapter Cap/Control Dial Tool Silicone Lubricant 1 1 1 1 1 1 2 2 1 1 OFF-LINE PARTS Included with Model 5430 REF. 11* 12 13 14 15 16 17 01-22-8620 01-22-7800 01-22-7690 01-22-7700 01-22-7850 01-22-7790 01-22-7910 2" X 1/2" Bushing 90° Elbow Small Clamp 6' PVC Tubing Scoop Gasket Venturi Scoop Scoop Clamp 2 2 4 1 2 2 2 11 POOL FROG Cycler Maintenance Replacing the Control Dial O-Rings ® Replacing Cap O-Ring 1. · Using a needle nose pliers, find the snap ring tail located at approximately the five o'clock position under the control dial. 1. 2. · Pull down and out of the groove. · Hold cap in front of you upside down with the o-ring groove facing up. Place one end of o-ring into cap groove at the point closest to you. Hold o-ring down with the thumb and forefinger of one hand. 2. 3. · Using a large screwdriver, loosen the control dial. Carefully pry the dial until it pulls out. · Take hold of the far end of the o-ring with the thumb and index finger of the other hand. Roll o-ring slightly back towards you as you stretch the o-ring into the remainder of the cap groove. 4. OTHER COPY? SILICONE LUBRICANT COPY COPY COPY COPY · Carefully replace the rubber o-ring without stretching it. Apply silicone lubricant, that came with your POOL FROG® Cycler, on o-ring. 3. xxxxx SLICONE LUBRICANT COPY COPY COPY · Lubricate o-ring often with silicone lubricant that came with your POOL FROG® Cycler. DO NOT USE petroleum based lubricants. COPY 5. · Push control dial completely into the housing and turn the dial to setting 2. Replacing knob 6. · Insert the non-lipped end of snap ring into the groove opening beginning at the 5 o'clock position and push it up so that it threads itself around the control dial. [. . . ] Purchaser must present the sales receipt or other documentation verifying proof of purchase. This warranty does not cover defects caused by: Modification, alteration, repair or service of the unit contrary to the accompanying instructions; physical abuse to or misuse of the product or operation or installation in a manner contrary to the accompanying instructions. This warranty also excludes all costs arising from the installation, adjustment, removal or replacement of defective units or parts. This warranty also excludes any and all claims arising out of the chemicals used in the product or their characteristics. [. . . ]