User manual KING TECHNOLOGY PREVAIL FEEDER (ENGLISH)

[. . . ] (Follow directions for setting below. ) 2. · Shock the pool with chlorine to rid the water of all contaminants before beginning. Follow manufacturer's directions carefully. SETTING CONTROL DIAL 5. POOL SIZE 7, 000 9, 000 12, 000 15, 000 20, 000 (18') (21') (24') · Find your starting dial setting by matching up the parameters of your pool on the chart. 12 Hour Pump Run Time 1/2 hp 2. 5 3 3. 5 4 4. 5 PUMP SIZE 3/4 hp 1 hp 2 1 2. 5 3 3. 5 4 2 2. 5 3 3. 5 1 1/2 hp 3 3. 5 2 2. 5 3 24 Hour Pump Run Time 1/2 hp 1. 5 2 2. 5 3 3. 5 3/4 hp 1 1. 5 2 2. 5 3 PUMP SIZE 1 hp 1 1 1. 5 2 2. 5 1 1/2 hp 2 Gallons Diameter * * * * * 2. 5 3 1. 5 2 Dial settings based on 1. 5 ppm. * ­ Bypass installation recommended. RECOMMENDED FLOW RATE 20-60 gpm Test Strips · Do not add shock in or near the skimmer or into the Cycler as it could damage equipment, risk potential explosion or discolor your pool surface. 6. Pool and Spa Test Strips · For the first week test the pool water daily for free chlorine to ensure correct dial setting. Continue to test weekly throughout the season. [. . . ] DO NOT OVER TIGHTEN. · DO NOT USE CAP TOOL TO TIGHTEN CAP. FOR REMOVAL ONLY. 7. Opening in Pac Key in Cycler · Insert Pac into Cycler, lining up the openings in Pac with keys in Cycler. NOTE: Openings are a different shape than keys. 10. · Replace side knob on the Cycler. 8. · Insert Pac into Cycler. Avoid sparks, open flame or smoking when handling the Pac. 7 Pool Maintenance Winterizing 1. Test Strips Pool and Spa Test Strips · Test water for free chlorine, pH and total alkalinity once a week. · Turn dial to Minimum. Unscrew side knob to relieve pressure. 2. · Remove cap. · Shock pool once a week. Follow manufacturer's directions. 3. · Unscrew knob from the front of Cycler. Allow all water to drain. · Replace Chlorine Pac when empty, approximately once a month. 4. · If Pac still contains chlorine wrap in plastic bag and store in shed or garage away from children and pets. Make sure Pac is away from open flame or anything metal. OTHER COPY? SILICONE LUBRICANT · Lubricate cap o-ring every time Pac is replaced. COPY COPY COPY 5. COPY · Replace the cap and knobs loosely. 8 Cycler Maintenance Replacing the Control Dial O-Rings Replacing Cap O-Ring 1. Hold cap in front of you upside down with the o-ring groove facing up. Place one end of o-ring into cap groove at the point closest to you. Hold o-ring down with the thumb and forefinger of one hand. 1. · In the back of the Cycler depress tab at end of locking pin with a pen or screwdriver and pull pin out of dial. 2. · Turn control dial back and forth as you pull it out of the housing. 2. Take hold of the far end of the o-ring with the thumb and index finger of the other hand. Roll o-ring slightly back towards you as you stretch the o-ring into the remainder of the cap groove. 3. OTHER COPY? SILICONE LUBRICANT COPY COPY COPY COPY · Replace both o-rings. Please note: the back oring has a loose fit in the groove. Apply silicone lubricant that came with your Cycler on o-rings. OTHER COPY? SILICONE LUBRICANT COPY COPY COPY 3. Lubricate o-ring often with silicone lubricant that came with your Cycler. DO NOT USE petroleum based lubricants. COPY Replacing a Knob 4. · Carefully insert control dial back into housing. · To replace, simply unscrew and replace with the new one. · Front of Cycler 5. · Replace locking pin by pushing it through the slots on the dial until it locks into place. · Side of Cycler 9 Parts List 10 11 OTHER COPY? SILICONE LUBRICANT 12 COPY COPY COPY COPY 13 CYCLER DIAGRAM/PARTS LIST REF. # PART # DESCRIPTION 1&2 2 3 4 5, 6, 7 6 7 8&9 10 11 12 13 10 QTY. 1 1 1 1 1 1 1 2 1 1 1 1 01-22-1412 01-22-1920 N/A 01-22-9480 01-22-1441 01-22-1450 N/A 01-22-9941 01-22-1710 01-22-9790 01-22-9970 01-22-9980 Cap w/O-Ring Cap O-Ring Body Pressure Relief Valve Control Dial with O-Rings Control Dial O-Ring Set Control Dial Locking Pin Knob with O-Ring Nipple Kit Cap/Control Dial Tool Silicone Lubricant Pac Cutting Tool ATTENTION BUILDER: Call 800-222-0169 for an In Ground or Above Ground test cap to use at start-up to ensure proper back pressure. TOOLS NEEDED: Screwdriver Filter Installation Pipe Wrench 2. INCLUDED WITH CYCLER: One Hose Adapter 1 1/2" X 1 1/2" X 1 1/4" 1. Apply teflon tape to each threaded end of nipple. Screw one end of nipple into the filter return. Tighten turning 1 to 2 revolutions with wrench. Screw eitheropen of Cycler on to nipple end until upright and secure. Teflon Tape MATERIALS NEEDED: One 6" X 1 1/2" TBE PVC Nipple 4. Apply teflon tape to threaded end of hose adapter. Screw adapter into the other side of Cycler. Tighten turning 1 to 2 revolutions with wrench. [. . . ] Purchaser must present the sales receipt or other documentation verifying proof of purchase. This warranty does not cover defects caused by: Modification, alteration, repair or service of the unit contrary to the accompanying instructions; physical abuse to or misuse of the product or operation or installation in a manner contrary to the accompanying instructions. This warranty also excludes all costs arising from the installation, adjustment, removal or replacement of defective units or parts. This warranty also excludes any and all claims arising out of the chemicals used in the product or their characteristics. [. . . ]