User manual KINGSTON KHX2250C9D3T1FK6GX MEMORY MODULE SPECIFICATION

[. . . ] TECHNOLOGY Memory Module Specification KHX2250C9D3T1FK3/6GX 6GB (2GB 256M x 64-Bit x 3 pcs. ) DDR3-2250MHz CL9 240-Pin DIMM Kit w/ Fan DESCRIPTION: Kingston's KHX2250C9D3T1FK3/6GX is a kit of three 256M x 64-bit (2GB) DDR3-2250MHz CL9 SDRAM (Synchronous DRAM) memory modules, based on sixteen 128M x 8-bit DDR3 FBGA components per module. [. . . ] The JEDEC standard electrical and mechanical specifications are as follows: This special kit part number includes Kingston's HyperX high-performance cooling fan assembly (KHX-FAN). FEATURES: JEDEC standard 1. 5V ± 0. 075V Power Supply VDDQ = 1. 5V ± 0. 075V 667MHz fCK for 1333Mb/sec/pin d ye Ke 8 independent internal bank d ye Ke d Programmable CAS Latency: 5, 6, 7, 8, 9, 10 ye Ke Posted CAS Programmable Additive Latency: 0, CL - 2, or CL - 1 clock Programmable CAS Write Latency(CWL) = 7(DDR3-1333) 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address "000" only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%) On Die Termination using ODT pin Average Refresh Period 7. 8us at lower then TCASE 85°C, 3. 9us at 85°C < TCASE . 95°C Asynchronous Reset PCB : Height 2. 401" (61. 00mm) w/ heatsink, double sided component PERFORMANCE: CL(IDD) Row Cycle Time (tRCmin) Refresh to Active/Refresh Command Time (tRFCmin) Row Active Time (tRASmin) Power UL Rating Operating Temperature Storage Temperature 9 cycles 49. 5ns (min. ) 110ns 36ns (min. ) 1. 800 W (operating per module) 94 V - 0 0o C to 85o C -55o C to +100o C Document No. 4805619-001. A00 05/28/10 Page 1 Kingston MODULE DIMENSIONS: TECHNOLOGY 30. 00 Units: millimeters 133. 35 18. 80 15. 80 11. 00 8. 00 0. 00 0. 00 w/ heatsink assembly mm 61 01 2. 4 Document No. 4805619-001. A00 54. 70 Page 2 Kingston KHX-FAN HyperX Cooling Fan Assembly DESCRIPTION: This document describes Kingston's HyperX memory module cooling fan assembly. If you are looking to maximize the performance potential of your HyperX memory. . . With twin fans focusing air directly onto your HyperX modules, your modules will run cooler, even in the most demanding environments. The mechanical and electrical specifications are as follows: PERFORMANCE: Rated Voltage Operational Voltage Input Current Input Power RPM Speed Control Type Signal Output Max. Air Pressure At Zero Flow Accoustical Noise 12 VDC 8 - 13. 5 VDC 0. 09 amp 1. 08 watt 3000 ± 10% Frequency Generator (FG) 0. 43 m3/min 15. 02 CFM 2. 31 mm-H2O 0. 09 inch-H2O 25 (28 max. ) dB-A HyperX Cooling Fan Assembly Document No. [. . . ] 4805619-001. A00 Page 6 Kingston INSTALLATION (cont. ): Document No. [. . . ]