User manual KINOTON FP 30 D MANUAL 1

[. . . ] The FP 30 D projector is only to be employed for its intended purpose and is only used when functioning absolutely perfectly . Serious danger may result from improper use of the system causing injury to the user or a third person, or damage may be done to the system or other items in the vicinity. Faults that could adversely affect safety must be rectified immediately. The projector cannot be used before faults are rectified. Operating Manual 1-1 Intended Purpose The FP 30 D projector is only suitable to reproduce 35 mm films and sound. [. . . ] Fasten positive cable (anode) of xenon bulb with connecting bolt (arrow). 6. Close lamphouse doors and fasten screws. Operating Manual 2-19 2. 4. 1. 3 Adjusting the Intensity of Currents Turn hand wheel for rectifier control and set intensity of current in a way you see in the following table. You can read the values on ampere meter (arrow). Figure 2-11 Adjusting intensity of currents Lamp capacity [W] 700 1000 1600 65 70 2000 70 85 2500 90 100 3000 4000 135 150 5000 140 150 7000 160 165 Setting value [A] 37 50 max. current [A] 45 55 100 110 NOTE Read the data sheet which is delivered with xenon bulb. 2-20 : Kinomedia. net ® , 2008 . FP 30 D 2. 4. 1. 4 Adjusting the Illumination of Screen xenon bulb to film gate stabilizing magnet axial adjustment horizontal adjustment vertical adjustment Figure 2-12 Adjusting illumination of screen You can adjust the xenon bulb against mirror in three levels (horizontal and axial ). Open lamphouse and loosen the bulb stay (white arrow). DANGER Open lamphouse after a waiting period of 10 minutes. , vertical The current of lamp and rectifier must be switched off all-polo. Work at open lamphouse to be carried out has to be done with protective suit, cloves and face shield. You can seriously hurt yourself when xenon bulb explodes and broken glass is flying around. 2. Carry out the following adjustments through the associated holes in lamphouse housing. With the aid of the hexagon screw , the xenon lamp is adjusted as much along the optical axis until only a reduced round illuminated spot can be seen on screen. By turning adjusting screws right left (horizontally) and up down (vertically) you have to bring this light spot precisely into the middle of the screen. Operating Manual 2-21 7. By turning the hexagon screw , mount the spot until the screen is illuminated evenly. If necessary adjust the screws / a little bit. NOTE Whenever in extreme special cases the described way to adjust is not possible, you can change the mirror position with the aid of the adjusting screws of mirror holder. The light arc adjustment is to be carried out by experts only, see operating manual Universal Lamphouse . 2. 4. 1. 5 Inserting Heat Filter A heat filter is necessary from a lamp capacity of 2500 W onwards. It protects film gate from too much heat. ATTENTION The heat filter is a reflection filter, therefore you have to watch out for the reflection side of filter to be directed to xenon lamp. You can see the edge of reflection coating when you look at the small side of filter holding it against the light. The reflection side is slightly adhesive. Touch the filter on one edge with your fingers - On the adhesive side you will see a fingerprint. Lamphouse up to 2000 W 2000 to 7000 W Figure 2-13 Heat filter clamping bar heat filter holders 1. Lamphouse up to 2000 W: Insert filter under clamping bar fasten screws of clamping bar. [. . . ] board with solar cell sensor for reading metal foil tape guide roller p. board with CCD-unit digital sound device sound optics (digital) Figure 3-27 Analog and digital sound devices LEDs holder analog LED sound roller digital LED holder of digital LED sound pressure roller Figure 3-28 LEDs NOTE The Reverse-Scan Sound Device is delivered factory-checked and set. New adjustments are necessary when changing parts. Allow change and adjustments to be carried out by experts or service men from KINOTON only. [. . . ]