User manual KITCHENAID ARTISAN 5KSM6521XEFB

[. . . ] 00 Suomi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 00 Dansk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 00 Íslenska. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 00 Русский. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Scrapping the product - This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE). - By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. - The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic equipment. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. 7 W10648168A_ENv03. indd 7 12/11/13 11:48 AM English PARTS AND FEATURES Motor head Attachment hub (see the “Attachments*” section) Speed control lever Beater height adjustment screw Attachment knob Bowl lift lever (not shown) Beater Shaft Bowl support Bowl handle* Locating pins Bowl* Dough hook* Flat beater* Wire whip* Pouring shield** * Material, style, and size may differ depending on model. **  ouring shield included only for models 5KPM5, 5KSM7580X and 5KSM7591X / Lid included only P for models 5KPM5 and 5KSM6521X. Lid** 8 W10648168A_ENv03. indd 8 12/11/13 11:48 AM ASSEMBLING THE STAND MIXER Attaching the bowl and beaters English 1 Turn speed control to “0” (OFF), and unplug Stand Mixer. 2 Place bowl lift lever into down position. Spring Latch Locating Pin 3 Fit bowl supports over locating pins; press down on back of the bowl until bowl pin snaps into the spring latch. If not securely snapped into place, bowl will be unstable and wobble during use. 4 Slip a beater (flat, wire whip, or dough hook) onto the beater shaft and press upward as far as possible. Turn beater to the right, hooking it over the pin on the beater shaft. Pouring Chute * 5 If using the pouring shield*, from the front of the Stand Mixer, slide the pouring shield over the bowl until it is centered. The bottom rim of the pouring shield should fit within the bowl. 6 Raise the bowl into mixing position by rotating the bowl lift lever counterclockwise to the straight up position. The bowl must always be in the raised position when mixing. NOTE: Rotate the pouring shield* so the motor head covers the U-shaped gap in the shield. The pouring chute will be just to the right of the attachment hub as you face the Stand Mixer. *  ouring shield included only for models 5KPM5, 5KSM7580X and 5KSM7591X P 9 W10648168A_ENv03. indd 9 12/11/13 11:48 AM ASSEMBLING THE STAND MIXER Adjusting beater to bowl clearance Your Stand Mixer is adjusted at the factory so the flat beater just clears the bottom of the bowl. If, for any reason, the flat beater hits the bottom of the bowl or is too far away from the bowl, you can correct the clearance easily. 1 Turn speed control to “0” (OFF), and unplug Stand Mixer. 2 Lower the bowl to the down position. 3 Turn beater height adjustment screw (A) slightly counterclockwise (left) to raise the flat beater; or turn clockwise (right) to lower the flat beater. Adjust so that the flat beater just clears the surface of the bowl. If you over adjust the screw, the bowl lift lever may not lock in place. NOTE: When properly adjusted, the flat beater will not strike on the bottom or side of the bowl. If the flat beater or the wire whip is so close that it strikes the bottom of the bowl, the coating may wear off the flat beater (for coated beaters) or wires on the wire whip may wear. Scraping sides of bowl may be necessary under certain conditions regardless of beater adjustment. The Stand Mixer must be stopped to scrape bowl or damage to Stand Mixer may occur. 10 W10648168A_ENv03. indd 10 12/11/13 11:48 AM OPERATING THE STAND MIXER Speed control guide - 10 speed Stand Mixers All speeds have the Soft Start feature that automatically starts the Stand Mixer at a lower speed to help avoid ingredient splash-out and “flour puff” at start-up, then quickly increases to the selected speed for optimal performance. Speed Used for Accessories Description For slow stirring, combining, mashing, starting all mixing procedures. Use to add flour and dry ingredients to batter, and add liquids to dry ingredients. Do not use Speed 1 to mix or knead yeast doughs. For slow mixing, mashing, faster stirring. Use to mix and knead yeast doughs, heavy batters, and candies; start mashing potatoes or other vegetables; cut shortening into flour; mix thin or splashy batters. For mixing semi-heavy batters, such as cookies. [. . . ] Service must be provided by an Authorized KitchenAid Service Center. A.  epairs when Stand Mixer R is used for operations other than normal household food preparation. B.  amage resulting from D accident, alterations, misuse, abuse, or installation/operation not in accordance with local electrical codes. KITCHENAID DOES NOT ASSUME ANY RESPONSIBILITY FOR INDIRECT DAMAGES. Customer service In U. K. and Ireland: For any questions, or to find the nearest KitchenAid Authorized Service Center, please find our contact details below. [. . . ]