User manual KLIPSCH IC-400-T

[. . . ] The tilebridge and loudspeaker are designed such that installation may be accomplished where access above the ceiling is not possible or may be difficult. The tilebridge is composed of three parts--a reinforcement ring and two rails. The two rails should be attached to the reinforcement ring using the four included screws as shown below. 4. [. . . ] To utilize the seismic tab, run a support wire from a secure point in the ceiling and attach it to the tab. Be sure to consult the construction codes in your area. Klipsch recommends the use of this tab in all installations as a secondary means of support. 1. 875W 3. 75W 7. 5W 15W 15W 7. 5W 3. 75W IC-400-T tap selectable 100V 70V 3. 75W 7. 5W 15W 30W 30W 15W 7. 5W IC-525-T tap selectable 100V 70V 7. 5W 15W 30W 60W 6. For installations using 70v/100v input connection, set the switch on the front panel to the desired setting. For applications where 8 Ohm impedance is desired, the switch should be set to 8 Ohms. Note: The speaker comes from the factory set at the lowest output setting (highest impedance). Using the flat of your hand, insert grille into speaker frame making sure it is securely seated and flush. 60W 30W 15W IC-650-T tap selectable 100V 70V IN - CEILING SPEAKERS I C - 4 0 0 - T , I C - 5 2 5 - T & I C - 6 5 0 - T S P E C I F I C AT I O N S IC-400-T FREQUENCY RESPONSE C O N T. O U T P U T @ 1 M SENSITIVIT Y 2. 83 V/1M C OV E R AG E DI Q N O M I N A L I M P E DA N C E DIAMETER C U TO U T D I A M E T E R OV E R A L L D E P T H MOUNTING DEPTH WEIGHT I N P U T C O N N E C TO R S T R A N S F O R M E R TA P S FINISHES TRANSDUCERS E N C LO S U R E T U N I N G 70-20k Hz +/- 4 dB 50 watts (14. 5V) 100 dB 86dB 80 degrees 8 dB 6. 3 8 ohms, min 4. 2 ohms when switch is set to 8 ohm position 9" 9. 125" 8. 313" 8" 6. 25 lbs. Te r m i n a l S t r i p 7 0 V: 15 W, 7. 8 W Black and White 5 " WO O F E R A N D 1 " T I TA N I U M D I A P H R AG M C O M P R E S S I O N D R I V E R O N A 2 " RO U N D T R AC T R I X H O R N Ve n t e d V i a A 1 " Tr a c t r i x p o r t IC-525-T FREQUENCY RESPONSE C O N T. O U T P U T @ 1 M SENSITIVIT Y 2. 83 V/1M C OV E R AG E DI Q N O M I N A L I M P E DA N C E DIAMETER C U TO U T D I A M E T E R OV E R A L L D E P T H MOUNTING DEPTH WEIGHT I N P U T C O N N E C TO R S T R A N S F O R M E R TA P S FINISHES TRANSDUCERS E N C LO S U R E T U N I N G 65-20k Hz +/- 4 dB 65 watts (16. 5V) 104 dB 89dB 10 5 d e g r e e s 6. 5 dB 4. 5 8 ohms, min 4. 2 ohms; switch set in 8 ohm position 9" 9. 125" 9. 188" 8. 875" 8. 25 lbs. Te r m i n a l S t r i p 7 0 V: 3 0 W, 15 W, 7. 7 5 " WO O F E R A N D 1 " T I TA N I U M D I A P H R AG M C O M P R E S S I O N D R I V E R O N A 3 . 5 " RO U N D X T M O D I F I E D T R AC T R I X H O R N Ve n t e d V i a A 1 " Tr a c t r i x p o r t IC-650-T FREQUENCY RESPONSE C O N T. O U T P U T @ 1 M SENSITIVIT Y 2. 83 V/1M C OV E R AG E DI Q N O M I N A L I M P E DA N C E DIAMETER C U TO U T D I A M E T E R OV E R A L L D E P T H MOUNTING DEPTH WEIGHT I N P U T C O N N E C TO R S T R A N S F O R M E R TA P S FINISHES TRANSDUCERS E N C LO S U R E T U N I N G 50-20k Hz +/- 4 dB 80 watts (18. 8 V) 106 dB 90dB 10 5 d e g r e e s 6. 5 dB 4. 5 8 ohms, min 4. 4 ohms; switch set in 8 ohm position 10" 10. 125" 10. 938" 10. 625" 11. Te r m i n a l S t r i p 7 0 V: 6 0 W, 3 0 W, 15 W, 7. 5 W 10 0 V: 6 0 W, 3 0 W, 15 W Black and White 6 . 5 " WO O F E R A N D 1 " T I TA N I U M D I A P H R AG M C O M P R E S S I O N D R I V E R O N A 3 . [. . . ] Any unauthorized repairs will void this Warranty. This Warranty does not cover product sold AS IS or WITH ALL FAULTS. REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. [. . . ]