User manual KLIPSCH IC-SW-8T2

[. . . ] Position tilebridge over cutout hole. The IC-SW-8T2 in-ceiling speaker is designed for music reinforcement applications. Unobtrusive, these loudspeakers are engineered for easy, versatile installation. The IC-SW-8T2 features a transformer-less design for 70. 7V/100V distributed-line systems. Some of the benefits of this design are: Elimintation of transformer saturation at high output levels, elimination of transformer insertion losses, improved bandwidth (particularly at low frequencies), and improves power transfer to the loudspeaker at low frequencies. [. . . ] Connection to the low impedance terminal could result in speaker damage, amplifier damage, or both. 2. To install your IC-SW-8T2 cut out a hole in the ceiling using either the cardboard cutout template provided with your speakers or consult the measurements below. Pull wiring through hole. IC-SW-8T2 12. 5 " Ro u n d 5. Insert the speaker into the cutout hole. With a #2 Phillips screwdriver, tighten the four dog clamps until they are seated securely against the ceiling surface. For installations using 70v/100v input connection, set the switch on the front panel to "70V/100V". For low impedance, stereo applications, the switch should be set to 8 ohms stereo. For low impedance, mono applications, the switch should be set to 4 ohm mono. In all cases, please make sure the speaker wires are connected to the appropriate terminal on the back. 60W 70 30W 10 0V IC-SW-8T2 tap selectable 7. Using the flat of your hand, insert grille into speaker frame making sure it is securely seated and flush. Seismic Tab A seismic tab, located on the back of the speaker, is used as a secondary security point. Some construction codes may require its use. To utilize the seismic tab, run a support wire from a secure point in the ceiling and attach it to the tab. Be sure to consult the construction codes in your area. Klipsch recommends the use of this tab in all installations as a secondary means of support. V 60W 120W IN - CEILING SUBWOOFER IC-SW-8T2 S P E C I F I C AT I O N S IC-SW-8T2 FREQUENCY RESPONSE C O N T. O U T P U T @ 1 M SENSITIVIT Y 2. 83 V/1M C OV E R AG E DI Q N O M I N A L I M P E DA N C E DIAMETER C U TO U T D I A M E T E R OV E R A L L D E P T H MOUNTING DEPTH WEIGHT I N P U T C O N N E C TO R S T R A N S F O R M E R TA P S FINISHES TRANSDUCERS E N C LO S U R E T U N I N G 5 0 - 13 0 H z + / - 4 d B 150 watts (27 V) 111 dB 92 dB N/A N/A N/A 6 ohms, min 4. 9 ohms, switch set to mono or stereo position 14. 125" 14. 25" 13. 625" 13. 313" 23 lbs. Te r m i n a l S t r i p 7 0 V: 6 0 W, 3 0 W 10 0 V: 12 0 W, 6 0 W White 8 " Wo o f e r A N D 8 ' D r o n e Bandpass via an 8" Drone ©2003 Klipsch Audio Technologies All Rights Reserved Specifications Subject to Engineering Changes Klipsc h Limited Warranty KLIPSCH, AUDIO TECHNOLOGIES ("KLIPSCH") warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below) for a period of five (5) years from the date of purchase. During the Warranty period, KLIPSCH will repair or replace (at KLIPSCH's option) this product or any defective parts (excluding electronics and amplifiers). [. . . ] REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. KLIPSCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE. Some states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you. [. . . ]