User manual KLIPSCH LIGHTSPEAKER 5

[. . . ] Tech Support: 1-800-KLIPSCH One LightSpeaker® 5 installs in 15 minutes or less! State-of-the-art LIGHT & SOUND Note: The LightSpeaker® is an add on unit to an existing LightSpeaker® System. You need a LightSpeaker® Transmitter to supply audio and control the lights on this unit. The Transmitter and Remote discussed in the manual are sold separately. OWNER'S MANUAL 1 Tech Support: 1-800-KLIPSCH The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Le symbole de l'éclair fléché dans un triangle équilatéral, a pour but d'avertir l'utilisateur de la présence non isolées d'une «tension dangereuse» dans le boîtier du produit que mai d'une magnitude suffisante pour constituer un risque d'électrocution pour les personnes. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. [. . . ] Your LightSpeaker® 5 is designed to fit directly into most 5" (R30) and 6" (R40) down light cans by simply removing the existing light and, in the same manner as a light bulb, re-installing your LightSpeaker® 5 in its place. You may simply test fit your LightSpeaker® 5. If your LightSpeaker® 5 fits directly into your recessed lighting fixture without any modifications you can skip forward to Step 6. If your LightSpeaker® 5 does not fit either because the trim ring/reflector opening is too small or the lighting fixture is not set deep enough, please go to www. klipsch. com or refer to your Complete System Manual. Your LightSpeaker® 5 comes with their own integrated trim ring. Choose your trim ring based on either A or B below and place the LightSpeaker® 5 trim ring over the back of the LightSpeaker® 5. Be sure the finished side is facing out. Upon completion of the install, this trim ring should fit snuggly and uniformly to the ceiling and should also seat properly around the entire edge of your LightSpeaker® 5. A) The thicker trim ring will be used when your LightSpeaker® 5 is installed into a 6" lighting fixture. 10 Tech Support: 1-800-KLIPSCH B) The thinner one is used when installed into a 5" fixture. As long as the trim ring covers the edges of the lighting fixture and any rough drywall edges you may use either trim ring; it will not affect the performance of your LightSpeaker® 5. Your LightSpeaker® 5 is equipped with a unique mounting system. The three SimpleTabsTM, on the back of the speaker can be rotated outward and when the LightSpeaker® 5 is pressed into the housing, hold it centered and securely in place. SimpleTabsTM You will now adjust the Simple TabsTM on the back of the LightSpeaker® 5 to either A (6" recessed light fixture) or B (5" recessed light fixture). If you are installing into a 5" recessed lighting fixture, rotate each of the SimpleTabsTM out to position "B" on the top of the LightSpeaker® 5 unit. 11 Tech Support: 1-800-KLIPSCH If you are installing into a 6" recessed lighting fixture, rotate each of the SimpleTabsTM out to position "A" on the top of the LightSpeaker® 5 unit. SimpleTabsTM Step 6: Setting the Zone and L/R Stereo Switches. A) Set the zone switch on the back of the LightSpeaker® 5 to one, unless you are setting up a two zone system. For more on zones see Complete System Manual or go to www. Klipsch. com. 12 Tech Support: 1-800-KLIPSCH B) Set the left/right stereo switch. "L" if it is the left speaker, "R" if it is the right speaker. For additional information see Selecting LightSpeaker® 5 Locations on page 16. C) Your LightSpeaker® 5 system allows you to install up to 4 pair of (or 8 total ) speakers. If you are installing more than one pair of LightSpeakers® 5 you will probably want to divide your home into zones. See Complete System Manual or go to www. Klipsch. com. Step 7: Installing your LightSpeaker® 5 into the recessed light fixture: A) Easiest Install: If you skipped steps 4 and 5, and your LightSpeaker® 5 fits with no modifications, screw it into the lighting fixture. 3) When the lens pops up, gently pry it away from the housing, being gentle and making sure not to break the tabs. 15 Tech Support: 1-800-KLIPSCH B) Removal of the lens AFTER your LightSpeaker® 5 has been installed. [. . . ] Proof of purchase in the form of a bill of sale or receipted invoice from an authorized dealer, which is evidence that this product is within the Warranty period, must be presented or included to obtain Warranty service. This Warranty is invalid if (a) the factory-applied serial number has been altered or removed from this product or (b) this product was not purchased from a KLIPSCH authorized dealer. You may call 1-800-KLIPSCH to confirm that you have an unaltered serial number and/or you purchased from a KLIPSCH authorized dealer. This Warranty is only valid for the original purchaser and will automatically terminate prior to expiration if this product is sold or otherwise transferred to another party. [. . . ]