User manual KLIPSCH SF1BK

[. . . ] 8900 Keystone Crossing, Suite 1220 Indianapolis, Indiana 46240 1. KLIPSCH · www. klipsch. com Make sure you return your warranty card so that we may keep you up-to-date on new Klipsch products and promotions. As always, if you have any questions, contact your local authorized Klipsch dealer. For your records: Model Serial Number Date Purchased Dealer Name 193110 15M1199 SP-1, SF-2, SF-1, SB-3, SB-2, SC-1, & SS-1 LOUDSPEAKERS Owner's Manual & Warranty CAUTION: RISK OF ELECTRIC SHOCK!To reduce the risk of electric shock and fire, do not remove the cover or back plate of this device. [. . . ] (21. 36kg) Height: 37" (93. 98cm) Width: 9" (22. 86cm) Depth: 14" (35. 56cm) Cabinet: Medium density fiber board construction (MDF) Finish: Woodgrain vinyl veneer Voltage: 110/120VAC 60Hz Export version: 230VAC 50/60Hz SC-1 Sensitivity: 95dB @ 1 watt / 1 meter Bandwidth: 60Hz­20kHz±3dB Nominal Impedance: 8 ohms Crossover Frequency: 2. 2kHz Power Handling: 100 watts maximum continuous (400 watts peak) Enclosure Type: Sealed Drive Components: Two-way system using one 1" (2. 54cm) K-101-S neodymium magnet, aluminum dome compression driver with a 90° x 60° Tractrix Horn and two 5. 25" (13. 3cm) K-1079-SV magnetically shielded woofers featuring polymer housings and IMG cones Net Weight: 15 lbs. (6. 78kg) Height: 6. 5" (16. 5cm) Width: 18" (45. 72cm) Depth: 7. 5" (19. 1cm) Cabinet: Medium density fiber board construction (MDF) Finish: Black matte vinyl SS-1 Sensitivity: 94dB @ 1 watt / 1 meter (equivalent sound energy) Bandwidth: 60Hz­20kHz±3dB Nominal Impedance: 8 ohms Crossover Frequency: 2kHz Power Handling: 100 watts maximum continuous (400 watts peak) Enclosure Type: Sealed Drive Components: Two-way system using two 1" (2. 54cm) K-101-S neodymium magnet, aluminum dome compression drivers with 90° x 60° Tractrix Horns and one 5. 25" (13. 3cm) K-1076-S woofer featuring a polymer housing and IMG cone Net Weight: 8. 5 lbs. (3. 9kg) Height: 6. 75" (17. 15cm) Width: 15" (38. 1cm) Depth: 6" (15. 24cm) Cabinet: Medium density fiber board construction (MDF) Finish: Black or white This product complies with the essential requirements of EMC directives 89/336/EEC and 73/23/EEC (inclusive of 93/68/EEC) and carries the CE mark accordingly. CE Wall Mounting · Install the four rubber stick-on bumpers (one on each corner of the rear panel of the speaker) to provide clearance for the speaker wire between the wall and cabinet. This will also prevent the speaker from marring the wall. · Cut out the template on the back cover of the owner's manual to assist in obtaining proper spacing of the two mounting holes. If the template is not available, space the mounting screws 4 9/16" apart on a vertical line. Allow at least 11/2" of clearance space above the top screw. · Check the vertical orientation of the marked hole locations with a torpedo level before drilling. · Use a #10 or #12 (21/2 - 3"long) pan head wood screw to mount into the wall stud. · Check the fit of the screw head in the keyhole fitting before installation as screw head sizes do vary. · Drill the proper size pilot holes at the marked positions and install the screws into the wall stud. Leave the back surface of the screw head protruding about 1/4-inch from the wall surface. This will facilitate hooking the keyhole bracket over the screw head with the rubber feet installed. The clearance between the wall and the screw head may need to be adjusted to achieve a proper fit. If a stud is not available, use the proper type and weight rating of drywall or masonry anchor appropriate for the wall construction. Please consult your dealer, custom installer or a building contractor in this situation. !! · Do not use the keyhole mounting brackets for ceiling installations! How to Connect the Synergy Series Speakers AC POWER / SP-1 ONLY Since your SP-1 has an internal subwoofer power amplifier, it must be plugged into a nearby AC wall outlet. The SP-1 should be unplugged from the AC power with the power switch in the OFF position during hook up and installation. To eliminate a tripping hazard, all connections should be unplugged from the back panel of the speaker if it is being moved. Avoid extremely long extension cords of small gauge since they can impair the performance of the subwoofer amplifier and present a potential fire hazard. If the SP-1 will not be used for an extended period of time, unplug the power cord from the AC power outlet. Note: 230 volt models are not supplied with an AC power cord, but are equipped with an IEC-type power cord socket. [. . . ] Flush mounted components and narrow front profiles are combined with time-aligned drivers and simple, minimum phase filter networks to provide truly extraordinary soundstaging. The rear soundfield, in a full surround system configuration, is provided by the Klipsch SS-1 Wide Dispersion Surround TechnologyTM speakers. These speakers contain an array of three drivers that flood the back of the listening room with high quality direct and reflected sound, providing both pinpoint rear channel imaging and ambient envelopment. Speaker Placement SYNERGY MAIN SPEAKERS Both speakers should be placed on the same wall facing the listening area. Space the loudspeakers so they are between six and 15 feet apart. [. . . ]