User manual KOMPERNASS PARKSIDE PEBH 900 ROTARY PERCUSSION DRILL

[. . . ] Make sure you always use the auxiliary side handle whilst operating the drill. Look after your health: Wear ear defenders - also wear safety glasses and a breathing /dust mask. Always keep the power cable well out of the working area and fed to the rear of the machine. The drill is not to be operated by persons under 16 years old. 4 www. kompernass. com +++ www. kompernass. com +++ www. kompernass. com +++ AREA OF USE The PEBH 900 rotary percussion drill can be used successfully for light chiselling work. [. . . ] You should be able to hear clearly the additional chuck engaging if it has been inserted correctly. Releasing the locking/unlocking cap locks the mechanism. Check by pulling the tool that it has correctly locked. REMOVING ADDITIONAL CHUCK FOR STRAIGHT SHANK DRILL BITS To remove the additional chuck, pull the locking/unlocking cap backwards again and remove the additional chuck. 5 www. kompernass. com +++ www. kompernass. com +++ www. kompernass. com +++ SELECT FUNCTION WARNING !Only use / set the function selector after the motor has reached a standstill. You can set the function selector to the symbol appropriate to the area of use. There are three function settings as follows: CHISELLING ROTARY PERCUSSION DRILLING DRILLING / SCREWING SELECT DIRECTION OF ROTATION WARNING !Only use / set the forward / reverse selector after the motor has reached a standstill. Note: The maximum speed for heavy work is only available in forward mode. The drill always works at a lower speed in reverse mode. PRESELECT SPEED WARNING !Only use / set the speed control wheel after the motor has reached a standstill. You can use the speed control wheel to preselect the operating speed to the exact value appropriate to your work. This means you can easily and conveniently drill into e. g. In addition, it allows you to avoid the drill bit slip ping and breaking material out around the hole whilst drilling. Note: If you select a low speed, this means the ON / OFF trigger will only press in a limited amount (as a result of the reduced speed pre selected). If you need the maximum power for your work, use the highest preselected speed (turn speed control wheel down ( )). LOW (­) SPEED: HIGH (+) SPEED: turn the speed control wheel turn the speed control wheel up ( ) down ( ) USING THE AUXILIARY HANDLE Warning !On safety grounds, make sure you always use the auxiliary side handle whilst operating the PEBH rotary percussion drill. You can alter the position of the auxiliary side handle by loosening the wingnut and swivelling the handle. The handle can be engaged in various positions. Recommendation: Set the handle in the horizontal position (at 90° to the drill body). [. . . ] 21, D-44867 Bochum, Germany, hereby declare that this product conforms with the following EC regulations: EC machine guideline: EC low voltage regulations: Electromagnetic compatibility: Applicable harmonised standards: (89/392 EEG), (91/368 EEG), (93/44 EEG), (93/68 EEG) (73/23/EEG), (93/68 EEG) (89/336 EEG), (92/31 EEG), (93/68 EEG) EN 50144-1:1998, EN 50144-2-6:1996, EN 55014-1:1993+A1+A2 EN 61000-3-2:1995+A1+A2, EN 61000-3-3:1995, EN 55014-2:1997 PEBH 900 rotary percussion drill Description: Bochum, 31. 03. 2003 Hans Kompernaß - Managing Director - 7 Warranty This piece of equipment is covered by a 36-month warranty as of the date of purchase. The equipment was produced with the greatest of care and underwent thorough testing before delivery. In the unlikely event of detecting a functional defect, please return the equipment in its original packaging with the proof of purchase (if available) to the closest service address. Damage caused due to improper handling as well as regular wear of the parts are not covered by this warranty. [. . . ]