User manual KONICA MINOLTA 4060

[. . . ] QMS® 4060 Print System Getting Started 1800462-001C Trademarks The following are trademarks or registered trademarks of their respective owners. Other product names mentioned in this manual may also be trademarks or registered trademarks of their respective owners. Registered trademarks are registered in the United States Patent and Trademark Office; some trademarks may also be registered in other countries. QMS, the QMS logo, Crown, and the Crown seal are registered trademarks of QMS, Inc. [. . . ] Insert and turn the developer bottle clockwise 180° (1/2 turn) to lock the bottle in place and begin filling. 2-48 QMS 4060 Print System Getting Started Installing Consumables 6 When the bottle is empty, gently tap it several times to make sure all of the developer has loaded. 7 Turn the developer bottle 180° counterclockwise and lift it up to remove it. Setting Up Your Printer 2-49 Installing Consumables 8 Close the developer fill lid. 9 Press the Select button on the control panel. The display message window shows INSERT BOTTLE SELECT WHEN DONE Offline Menu Select LETTER LETTER LEGAL Previous Next 10 Remove the small cap from the side of the developer bottle. 11 Turn the cap around and place it in the storage position on the bottle as shown. 2-50 QMS 4060 Print System Getting Started Loading the Paper Trays 12 Insert the developer bottle into the storage position. v Caution: In the storage position the developer bottle is used whenever the developer hopper is purged. Make sure the cap is removed and the bottle is in the correct position. 15 Press the Offline button on the control panel to place the printer on line. The printer will begin an automatic cycle to set the toner density. After about two minutes you should get a start-up page. Loading the Paper Trays The QMS 4060 Print System includes three 500-sheet adjustable paper trays. All three paper trays hold either A3, A4, A5, B4, B5, Executive, 11"x17", Legal, or Letter size paper. The printer automati- Setting Up Your Printer 2-51 Loading the Paper Trays cally pulls paper from the tray. Loading paper in the tray involves the following steps: n n n n » Opening the tray Setting the correct paper size for the tray (if necessary) and paper size indicator Loading paper in the tray Closing the tray Note: Ensure that the tray size matches the paper size (for example, letter paper must be loaded only when the tray is set to letter size). Since the paper tray sends a paper size signal to the printer controller, using a wrong size paper will cause jamming or the image positioned incorrectly on the page. Setting Up the Paper Size for a Paper Tray » Note: All three paper trays are set up for letter-size printing from the factory. If you need to configure the trays for any other paper size, then follow this procedure. Otherwise, go ahead to the next section. 1 2 Open the tray that you wish to change paper size. Locate the blue locking thumbscrews in the paper tray. Paper Guides Locking Thumbscrews 2-52 QMS 4060 Print System Getting Started Loading the Paper Trays 3 Turn the thumbscrew counter-clockwise to unlock one of the paper size guides. You should be able to lift up and remove the paper size guide after unlocking it. OSE CL EN OP LTR 4 Move the paper size guide to the appropriate slots to align it with the paper size marker. You should be able to read the paper size (A3/A4, LTR/LGR, LEG, EX, B4, B5) in the small alignment holes built into the paper guide. OSE CL LT R B4 LGL B5 A5 Setting Up Your Printer EN OP LTR LGR 2-53 Loading the Paper Trays 5 Turn the dial to clockwise to lock the paper size guide. OSE CL LTR LT R 6 » 7 Repeat steps 1-5 for the other two paper size guides. Note: If you are setting up the tray for 11"x17" (ledger), the left paper guide is stored in a slot near the front section of the tray. Set up the tray paper size tabs on the rear of the paper tray. Use the following chart for reference or the label attached to the paper tray. :A5 :A4 :A3 - Tab is moved forward - Tab is moved backward :B5 :B4 :LGL :EXEC :LTR :LGR 8 Adjust the other paper trays, if necessary, using the same procedures. 2-54 QMS 4060 Print System Getting Started EN OP Loading the Paper Trays Setting Up the Paper Size Indicator 1 2 Open the plastic bag in the starter kit containing the papersize cards. Break off the label that indicates the correct paper size for each tray. LGR A3 EXEC LTR A4 B4 LGL A5 B5 LGR A3 EXE C LTR A4 B4 LG L A5 B5 3 4 Pull out each tray and push out the paper-size holder. [. . . ] Tray Tabs Standard Media Size Letter, Executive, A4, A5, Statement Installing Options C-53 Security Key Tray Tabs Standard Media Size B4, Legal, 11"X17", A3, B4(ISO) B5, B5(ISO) Access the Operator Control/Custom Input Bins configuration menu to select the standard paper size for the custom input bin. v Caution: If you do not set up the paper size in the Operator Control/ Custom Input Bins menu, the printer could select an incorrect paper size and your image will not be positioned correctly on the page. Security Key v Caution: Even though both the security and serial options have a DB9 interface, the connectors are keyed and they can't be interchanged. Make sure that you install the security key only in the slot marked SECURITY on the back of the printer. An optional security key is available to password protect the Operator Control and the Administration menus. [. . . ]