User manual KONICA MINOLTA BIZHUB-350-250 PH2-5 UM COPY 1-1-0

[. . . ] 350/250 Copy operations Contents 1 Introduction 1. 1 1. 2 Energy Star®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 What is an ENERGY STAR® Product?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Trademarks and registered trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] - Paper of the same size and type is loaded with the w orientation in one paper tray and with the v orientation in another tray. - The "Auto Paper Select" setting is selected. - The "Mixed Original" setting is not selected. If "Group" is selected and the finisher is installed, copies are fed out shifted to separate them. 1 In the Basics screen, touch [Finishing]. The Finishing screen appears. 2 Touch [Group]. bizhub 350/250 (Phase 2. 5) 4-55 4 Stapling copies (staple settings) Basic copy operation ! Detail In order for copies to be stapled, all of the following conditions must be met. - The paper width must be between 182 mm and 297 mm. - The paper length must be between 140 mm and 432 mm. - If the "Mixed Original" setting is selected, all copies must be printed with paper of the same width. If a staple setting is to be selected, select the orientation in which the document is positioned. If an Original Direction setting is not selected, the copies may not be stapled as desired. For details on specifying the document orientation, refer to "Selecting the document orientation (Original Direction settings)" on page 4-20. When finisher is installed Paper Weight 56 g/m2 to 90 g/m2 Paper Size A4 w/v, B5 w/v, A5 v A3 w, B4 w Loading Capacity (detected in either measurement) 1, 000 sheets 500 sheets 150 mm 75 mm 4-56 bizhub 350/250 (Phase 2. 5) Basic copy operation To bind copies with staples 4 1 In the Basics screen, touch [Finishing]. The Finishing screen appears. 2 Touch either [Corner Staple] or [2 Staples]. ­ If "Corner Staple" is selected, the copies are bound together with a staple in the upper-left corner. If "2 Staples" is selected, [Position Setting] appears in the screen. To select the binding position, continue with step 3. If a staple setting is selected, the [Sort] setting is automatically selected. To cancel the staple setting, touch [Corner Staple] or [2 Staples] again to deselect it. ­ ­ ­ 3 Touch [Position Setting], and then select the desired position. ­ Touch [Auto] to automatically determine the binding position according to the orientation of the loaded document. 4 Touch [Enter]. The Finishing screen appears again. bizhub 350/250 (Phase 2. 5) 4-57 4 Punching holes in copies (punch settings) Basic copy operation ! Detail If a punch setting is to be selected, select the orientation in which the document is positioned. If an Original Direction setting is not selected, holes may not be punched in the copies as desired. For details on specifying the document orientation, refer to "Selecting the document orientation (Original Direction settings)" on page 4-20. When finisher is installed Paper Weight 60 g/m2 to 90 g/m2 Paper Size A3 w to B5 w/v To punch holes in copies 1 In the Basics screen, touch [Finishing]. The Finishing screen appears. 2 Touch [Hole-Punch]. [. . . ] Scans a document exceeding the maximum 80 pages that can be loaded into the ADF by scanning the document in separate batches. The document can be scanned and treated as a single copy job. In addition, the scanning location can be switched between the original glass and the ADF during the scanning operation. Enlarge Display Erase Finisher Fold & Staple Folding Group Image Repeat Image Settings Insert Image Insert Sheet Job LCT Low Power Mode Margin Memory Scan 13-6 bizhub 350/250 (Phase 2. 5) Appendix 13 Term Minimal Mixed Original Definition Select this setting to produce a copy with the original image slightly reduced. Select this setting to detect the size of each document page and print a copy on paper of the appropriate size when a document with different page sizes is loaded together into the ADF. [. . . ]