User manual KONICA MINOLTA BIZHUB-500-420 PH2 UM SCAN 1-1-0

[. . . ] Contents 1 Introduction 1. 1 Trademarks and Registered Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 License information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 OpenSSL Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 About This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The AppleTalk settings are applied. 2 Note To cancel changes to the setting, touch [Cancel]. To quit specifying the Utility mode setting, touch [Exit] in the sub display area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode by touching [Close] in each screen until the screen for the Copy, Fax, Scan or Box mode appears. bizhub 500/420 (Phase 2) 4-89 4 4. 18 Specifying Settings From the Control Panel Enabling LDAP Settings The LDAP function to which the machine can connect and search and retrieve information can be enabled/disabled. Enabling LDAP Parameters The Enabling LDAP parameters are as follows: Item LDAP Function Description Set whether or not to use the LDAP function. To specify Enabling LDAP settings 1 2 3 4 In the Administrator Setting screen, touch [5 Network Setting]. (Refer to "To display the Administrator Setting screen" on page 4-10 for more details. ) In the Network Setting screen, touch [8 LDAP Setting]. In the LDAP Setting screen, touch [1 Enabling LDAP]. Specify the desired settings. 5 Touch [OK]. The LDAP function is set. 4-90 bizhub 500/420 (Phase 2) Specifying Settings From the Control Panel 4 2 Note To cancel changes to the setting, touch [Cancel]. To quit specifying the Utility mode setting, touch [Exit] in the sub display area. Otherwise, cancel the Utility mode by touching [Close] in each screen until the screen for the Copy, Fax, Scan or Box mode appears. 2 Reminder If the LDAP server settings are not specified correctly, network failure may occur. The server administrator should specify LDAP settings. bizhub 500/420 (Phase 2) 4-91 4 4. 19 Specifying Settings From the Control Panel Setting Up LDAP Settings The LDAP server can be registered and authentication settings can be specified. LDAP Server Registration Parameters The LDAP server registration parameters are as follows: Setting Up LDAP screen 1/6 Item LDAP Server Name Description Set the LDAP server name to be registered. Use the keyboard that appears in the touch panel to type in the server name (up to 32 characters). Set the maximum number of destinations to display after searching. To change the value, press the [C] (clear) key, and then use the keypad to type in the value (between 5 and 1000 destinations). Set the maximum wait time for the search operation. To change the value, press the [C] (clear) key, and then use the keypad to type in the value (between 5 and 300 seconds). Specify the initial setting of the search conditions when performing a detailed search. For details on specifying the setting, refer to "Initial Setting for Search Details" on page 4-100. Checks the connection to the LDAP server. The LDAP server settings can be reset to the default settings that were specified at the factory. When a reset confirmation message appears, touch [Yes]. Max. [. . . ] A protocol for sending and forwarding e-mail. Abbreviation for Simple Network Management Protocol. A management protocol in a network environment using TCP/IP. Abbreviation for Secure Socket Layer/Transport Layer Security. [. . . ]