User manual KONICA MINOLTA BIZHUB-PRO-C6500 CMS UM 2-1-0

[. . . ] Contents 1 Introduction CMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Notices to the customer who employs the CMS . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Registered trademark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 1. 1 Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] % Do not ignore these safety advices. Warning When conducting a part replacement operation, be sure to get guidance from the customer engineer. And also, read the CMS Replacement Instructions carefully before conducting a part replacement operation by following the prescribed procedure and using tools also prescribed. Be sure not to conduct any operations other than those described in the CMS Replacement Instructions. When the prescribed procedure and tools are not employed, this may cause damage to the copier or you may get injured. Before starting operations, be sure to unplug the power cords of the copier main body and the optional equipment from the power outlet. When the power cord is plugged into the power outlet, some electrical components may be energized even if the power switch is turned off. So, be careful not to get an electric shock. The temperature gets high in the vicinity of the fusing unit. Be careful not to come into contact with it, or you may get burned. Symbol CMS part replacement operation 7 WARNING Ignoring this warnings could cause serious injury or even death. % Do not ignore these safety advices. Warning Do not allow any metal parts such as clips, staples and screws to fall into the inside or opening of the copier. They may cause a short circuit to the internal parts of the copier, thus leading up to a risk of an electric shock or fire. Check the wiring harness for squeezing and any other damage. Current may leak, thus leading up to a risk of an electric shock or fire. Symbol bizhub PRO C6500 / bizhub PRO C6500e 1-5 1 Power plug Introduction 7 WARNING Ignoring this warnings could cause serious injury or even death. % Do not ignore these safety advices. Warning Be sure to avoid plugging or unplugging the power cord with a wet hand. You may get an electric shock. Symbol Be sure to plug the power cord securely into the power outlet. Otherwise, a fire may result, or you may get an electric shock. 7 CAUTION Ignoring this cautions could cause injury or damage to property. % Do not ignore these safety advices. Warning When unplugging the power cord from the power outlet, be careful not to pull the power cord. Otherwise, a fire may result with the power cord damaged, or you may get an electric shock. Symbol 1-6 bizhub PRO C6500 / bizhub PRO C6500e Introduction When any abnormal condition is found 1 7 WARNING Ignoring this warnings could cause serious injury or even death. % Do not ignore these safety advices. Warning When the copier gets hot abnormally, or when it gives out smoke, a foul smell or abnormal noise, turn off the power switch at once. And then be sure to unplug the power cord from the power outlet and contact our service technician. When the copier is let fall or when the cover is damaged, turn off the power switch at once. And then, be sure to unplug the power cord from the power outlet and contact our service technician. [. . . ] Turn the paper feed guide in the direction of the two arrows while pushing in the paper feed unit to the paper feed cover side, and remove the paper feed guide upward. ­ ­ When installing the paper feed guide, fit the three tabs in each positioning hole. When installing the paper feed guide, be sure to put the no paper detection actuator so that it protrudes out of the paper feed guide as shown in the figure on the left. 4-4 bizhub PRO C6500 / bizhub PRO C6500e DF-609 4 7 Remove the screw and remove the shaft securing plate. screw shaft securing plate paper feed unit C-clip C-clip bearing bearing 8 Remove the two C-clips. bizhub PRO C6500 / bizhub PRO C6500e 4-5 4 9 ­ DF-609 Slide the two bearings inward, and remove the paper feed unit. When removing the paper feed unit, be sure not to damage the arm with the shaft. cover plate tab arm shaft ­ ­ When installing the paper feed unit, make sure the arm is mounted on the shaft. [. . . ]