User manual KONICA MINOLTA CF5001 UM 00-GB 1.0.0

[. . . ] User Manual CF5001 Recycled paper is used for the inside pages of this manual. Thank you very much for your purchase of the CF5001. This Manual deals with making copies, correct handling of the machine, and precautions for safety. In order to maintain a satisfactory copying performance, please keep this Manual readily available for reference in the rear pocket of the machine. ENERGY STAR® Program The ENERGY STAR Program has been established to encourage the widespread and voluntary use of energy-efficient technologies that reduce energy consumption and prevent pollution. As an ENERGY STAR Partner, we have determined that this product meets the ENERGY STAR guidelines for energy efficiency grounding it on the following features. Auto Low Power This function conserves energy by lowering the set temperature of the fixing unit. [. . . ] In the event the Timer Interrupt password has not been entered by the Key Operator, the following message will display instead. Input copy time 0 hour(s) 05 minute(s) When the above message displays, proceed to step 4. 2. Enter the password. Enter a 4-digit number Timer Interrupt password using the keypad on the control panel. For setting the Timer Interrupt password, see p. 14-33. If an invalid password is entered, continue by entering the valid 4-digit password. 3. Press [START]. The following message will be displayed on the Basic Screen. Input copy time 0 hour(s) 05 minute(s) 4. 6. Set the hour for the interrupt use. 3 hours is 3) using the keypad on the control panel. 7 minutes is 07) using the keypad on the control panel. (00 ~ 59) Entering a number smaller than 5 will set the minute at 5. 7. Copying is available until the set time is up. When Timer Interrupt of the copier is finished, press [POWER SAVER ON/OFF] for one second or longer, then release it. The copier returns to the OFF condition and copying is again disabled. 8-3 Rotation This function allows you to utilize APS or AMS and copy the original documents onto size A4 or B5, irrespective of the copy paper feeding direction. By default, Rotation requires APS or AMS to function. The Key Operator can set this function ON, or to operate when APS, AMS or reduce functions. 14-42. Original Copy Rotation copying Original Copy Rotation copying A4R A3 A4 B5 A4 B4 Normal copying A4R A4R B5 B5R Normal copying B5R A4 B5R B5 The copier is initially set to activate the Rotation function automatically. Follow the procedure below to release/resume this function. 1. Touch ROTATION OFF on the Basic Screen to highlight it. When Rotation is released, the Rotation icon on the Basic Screen will disappear to indicate that this function is cancelled. 2. 8-4 Touch to deselect ROTATION OFF to resume this function. When Rotation is resumed, the Rotation icon will be displayed on the screen. Vertical/Horizontal Zoom Mode Use the Vertical/Horizontal zoom mode to reduce or enlarge vertical and horizontal dimensions, independently. Vertical/Horizontal Zoom Mode Specifications Vertical/Horizontal zoom range: 0. 250~4. 000 Incompatible Conditions: APS, AMS, Reduce & Shift in Image Shift The figure shown below is the sample image using the Vertical/Horizontal zoom. Length: 0. 500, Width: 0. 500 Length: 0. 500, Width: 1. 000 Length: 0. 500, Width: 2. 000 Length: 0. 500, Width: 4. 000 Width Length Length: 1. 000, Width: 0. 500 Length: 1. 000, Width: 1. 000 Length: 1. 000, Width: 2. 000 Length: 1. 000, Width: 4. 000 Length: 2. 000, Width: 0. 500 Length: 2. 000, Width: 1. 000 Length: 2. 000, Width: 2. 000 Length: 2. 000, Width: 4. 000 Length: 4. 000, Width: 0. 500 Length: 4. 000, Width: 1. 000 Length: 4. 000, Width: 2. 000 Length: 4. 000, Width: 4. 000 1. Touch ZOOM on the Basic Screen. 8-5 Vertical/Horizontal Zoom Mode (continued) The popup menu for setting a zoom ratio will be displayed. When starting a new copying job, be sure to close the RADF securely, then press [AUTO RESET]. 2. Touch the vertical zoom key on the popup menu to highlight it, then set the vertical zoom ratio. Use the keypad on the popup menu to enter a 4-digit vertical zoom ratio, or use arrow keys (c/d) to scroll to the desired ratio. Similarly, touch the horizontal zoom key to highlight it, then set the horizontal zoom ratio. 3. Touch OK. The popup menu disappears automatically and the specified zoom ratio will be displayed on the Basic Screen. 4. 7. 8-6 Select additional copy conditions, as desired. Enter the desired print quantity from the control panel keypad. See p. 3-10 for details on setting print quantity. Position original(s). See p. 3-9 for details on positioning originals. Press [START]. Vertical/Horizontal Zoom Mode (continued) The figure shown below is the sample image using the Vertical/Horizontal zoom with an original placed slanted on the platen glass. 30° Length: 0. 500, Width: 2. 000 Length: 2. 000, Width: 0. 500 30° Length: 0. 500, Width: 2. 000 Length: 2. 000, Width: 0. 500 8-7 Making Folded Booklet (Fold / Stitch & Fold) The Fold and Stitch & Fold modes are available only when the FN-9 Finisher option is installed. When any of these modes is selected, the Booklet feature is automatically selected and indicated on the Application Selection Screen. · When copying two-sided signature originals using the Fold or Stitch & Fold mode, release the automatically selected Booklet mode on the Application Selection Screen. [. . . ] · Printer centring adjustment: adjusts the mis-centring of images vertical to paper feed direction. · Scanner centring adjustment: adjusts the centring when scanning the platen original. · RADF centring adjustment: adjusts the centring when scanning the RADF original. Key Operator Mode Screen Centring Adjustment Menu Screen Printer Centring Adjustment Screen Scanner (Platen) Centring Adjustment Screen RADF Centring Adjustment Screen Procedure 1 Touch [24] Centring adjustment on the Key Operator Mode Screen to display the Centring Adjustment Menu Screen. 2 Touch the desired menu key to display the adjustment screen for each function. [. . . ]