User manual KONICA MINOLTA EP1031F

[. . . ] After you have read through the manual, keep it for ready reference. Please use this manual as a quick and handy reference tool for immediately CE Marking (Declaration of Conformity) We declare under our sole responsibility that the copier and options to which this declaration relates is in conformity with the specifications below. This declaration is valid for the area of the European Union (EU) only. Product Type Product Name Options Standards Copying Machine EP1031F MB-4 Safety : EN 60 950 / 1992 (Safety of information technology equipment, including electrical business equipment) EMC : EN 55 022 (Class B) / 1995 (Limits and method for measurement of radio disturbance characteristics of information technology equipment (ITE)) EN 55 082-1 / 1992 (Electromagnetic compatibility - Generic immunity standard Part1: Residential, commercial and light industry) EC 801-2 / 1991 (Electrostatic discharge requirement) IEC 801-3 / 1984 and IEC 801-3 / 1992 (draft) (Radiated electromagnetic field requirement) IEC 801-4 / 1988 (Electrical fast transient / burst requirement) Safety : 73 / 23 / EEC and 93 / 68 / EEC art. 13 EMC : 89 / 336 / EEC and 93 / 68 / EEC art. [. . . ] Copying Procedure Starting the Copy Cycle 1 Meter Count Toner Drum Dehumidify 2 5 8 0 3 6 9 C Paper A3 A4 A4 A5 @ @ @ @ @ @ B4 @ FLS. @ Inch % 50%~200% 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 100% 4 7 Book Auto Photo Lighter Darker Auto/Photo A Starting the Copy Cycle 2 1139O2360A Press the Start Key, if it is green. The Start Key turns orange when the copy cycle starts. Stopping a Multi-Copy Cycle Stop To stop a multi-copy cycle in progress, press the Stop Key. The Start Key soon turns green and the copier stops. The Multi-Copy Display shows the number of copies yet to be made. 1139O2592A 1139O2592A Making Copies 1 Check the control panel to make sure that you have set up your copy job correctly. Chapter 3 1158O027DA 40 2. Copying Procedure Manual Bypass Copying Use the Manual Bypass to make copies on paper not loaded in the Drawer, or to copy onto transparencies, translucent paper, or any other special paper. If the copier is equipped with a Multi Bypass Tray (option), you can load more than one sheet of paper for a continuous run. x Types of Paper · Plain paper (weighing 60 g/m2 to 90 g/m2) · Heavyweight paper (weighing 90 g/m2 to 157 g/m 2) · Transparencies, translucent paper x Paper Size · Width: 100 mm to 297 mm · Length: 140 mm to 432 mm x Capacity · Plain paper, heavyweight paper, transparencies, translucent paper . . . 1 sheet at a time Chapter 3 Making Copies <Multi Bypass Tray> · Plain paper: Approx. 50 sheets · Plain paper (once-copied paper) . . . · Heavyweight paper, transparencies, translucent paper: Approx. 20 sheets IMPORTANT When making multiple copies using OHP transparencies, set the Copy Tray into the upper position if there is no Sorter or Staple Sorter mounted. This causes the copier to initiate toner replenishing, which lasts for 90 seconds at maximum. NOTE · Do not turn the Power Switch OFF or open the Front or Right Door while the copier is replenishing toner. 47 3. Drum Dehumidifier Function During high humidity periods or when there are sudden rapid changes in humidity (especially when you are using a heater in winter), condensation*1 could form on the surface of the PC Drum*2, resulting in blotchy copies. In such instances, use the Drum Dehumidify Key to dry the surface of the PC Drum. 1142O152CA 1142O152CA Before a Drum Dehumidifier Operation After a Drum Dehumidifier Operation Meter Count Toner Drum Dehumidify Meter Count Toner Drum Dehumidify 1142O119CA 1 2 1142O119CA Press the Drum Dehumidify Key. This sets the copier into the Drum Dehumidifier Mode which lasts for 90 seconds. Make a copy to check that the copy image is clear. Run the Drum Dehumidifier cycle once again if the copy image is not yet clear. Useful Tip A copy cycle can be initiated even while the copier is in the Drum Dehumidifier Mode. NOTE The copier cannot be set into the Drum Dehumidifier Mode while it is warming up. *1: Condensation: A phenomenon in which small drops of water are formed on cold surfaces, such as the surface of the PC Drum. *2: PC Drum: Functions in the copier as film does in a camera. Auxiliary Functions 1142O149CB Chapter 4 48 4. User's Choice The copier has been set so that the most frequently used settings are automatically selected in the initial mode. The User's Choice allows you to select the default settings which are automatically selected in the initial mode according to your own needs. % 50%~200% 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 1158O028DA 1158O028DA By setting defaults for the paper size, zoom ratio and other settings that are most frequently used, time and effort to make extra settings will be eliminated when the copier is turned ON or when the auto reset function is activated. Chapter 4 For more details, consult your Technical Representative. Functions Available in User's Choice Auxiliary Functions Choice Code U-13 U-14 U-20 Function Default auto exposure level Default exposure mode/level Auto Panel Reset ON/OFF Choice Code U-21 U-28 Function Energy Saver ON Timing Auto Shut OFF Timing 49 4. [. . . ] Care of the Copier To keep your copier in good shape at all times, make the following daily checks and cleaning. Daily Checks Power Cord, Communications Cable, Ground Cable Item Is the copier placed on its power cord or other Cables?Is the copier placed on cables of other electrical equipment?Are the cord and cables free of damage or cracks?Has the cord or cable jacket frayed to expose the wires? [. . . ]