User manual KONICA MINOLTA EP1052

[. . . ] i EP1052 Thank you for choosing Minolta. This operator's manual explains how to operate the copier and replenish its supplies. It also gives some troubleshooting tips as well as general precautions to be observed when operating the copier. To ensure the best performance and effective use of your copier, read this manual carefully until you familiarize yourself thoroughly with its operation and features. [. . . ] Using the Manual Bypass Tray 1 2 1139O0150A Place the original on the Original Glass and make the control panel settings. Insert the copy paper into the Manual Bypass Tray. x This automatically starts the copy cycle. NOTES · Insert the copy paper one sheet at a time. · Do not insert a sheet of paper while the copier is warming up or in a multi-copy cycle. · The Book Copying Mode cannot be selected for manual bypass copying. 41 2. Copying Procedure Using the Multi Bypass Tray (Option) 1 2 1139O0130A Place the original on the Original Glass and make the control panel settings. Swing down the Multi Bypass Tray and slide the Paper Guide Plate to the size of the copy paper. NOTE Pull out the Multi Bypass Tray Extender if you are using larger paper. Chapter 3 · Before inserting, fan the 1139O0140A paper stack well if you are using transparencies or translucent paper. · Correct any curl if you are using thick paper. 4 5 1139O2360A Using the Key Pad, enter the number of copies to be made. Press the Start Key to start the copy cycle. 39 NOTES · Do not insert the paper while the copier is in the warm-up cycle or a multi-copy cycle. · The Book Copying Mode cannot be selected for manual bypass copying. Making Copies 3 Load a neat stack of copy paper on the Tray and insert it into the copier until it stops. Copying Procedure Making Copies Chapter 3 43 Chapter 4 Auxiliary Functions This Chapter explains about the Auxiliary functions that can be used for specific purposes. Chapter 4 1. Checking the Total Number of Copies Mode p. Toner Replenisher Function (Increasing the Image Density) p. Checking the Total Number of Copies Mode This function allows you to check the total count of the two counters of the copier. Meter Count Toner Drum Dehumidify 1142O152CA 1142O152CA Types of Counters · Total Counter Chapter 4 · Size Counter : Shows the total number of copies made since the installation of the copier. : Shows the number of copies made on paper of a size preset by the Technical Representative. Auxiliary Functions Counter Display The Zoom Ratio Indicator shows the upper 3 digits of the count. The Multi-Copy Display shows the lower 2 digits of the count. 50%~200% 1139O3790A Example: The count is 12, 345 (copies). 45 1. Checking the Total Number of Copies Mode Using the Meter Count Function Meter Count Toner Drum Dehumidify 1142O116CA 1142O116CA 1 Press the Meter Count Key once. The count of the Total Counter is shown across the Zoom Ratio Indicator and Multi-Copy Display. Meter Count Toner Drum Dehumidify 1142O116CA 1142O116CA 2 Meter Count Toner Drum Dehumidify 1142O116CA 1142O116CA 3 Press the Meter Count Key once again. This restores the copier to the state before entering the Meter Count Mode. Auxiliary Functions Chapter 4 Press the Meter Count Key again. The count of the Size Counter is shown across the Zoom Ratio Indicator and Multi-Copy Display. 46 2. (Increasing the Image Density) The copier tends to exhaust the supply of toner rapidly when making a number of copies from an original with dark solid areas. As a result, the image density of the copy will become lighter. In such a case, you can use the Toner Replenisher function to regain the normal image density quickly. Meter Count Toner Drum Dehumidify 1142O152CA 1142O152CA Original Copy Copy Made After Toner Replenishing Auxiliary Functions Chapter 4 1142O148CB Even if you continue making copies after the image density has become lighter, the copier will gradually recover the normal image density. The Toner Replenisher Mode can, however, be used to obtain the normal image density more quickly. Meter Count Toner Drum Dehumidify 1142O118CA 1142O118CA Press the Auxiliary Toner Replenishing Key. [. . . ] Action It could result in the copier or other electrical equipment malfunctioning. Turn the copier OFF immediately, unplug the power cord, and call your Technical Representative. * Communications Cable: Cable connecting the copier with options Original Glass Item Is the Glass dirty?Action Clean the Glass using the procedure given in "Cleaning. " p. 96 Call your Technical Representative. Is the Glass scratched? [. . . ]