User manual KONICA MINOLTA FN-113 UNPACKING/SET-UP INSTRUCTIONS

[. . . ] Setup Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 10. Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. Open the vertical transport section of the Finisher and remove tape and fixing brackets from the Stapling Unit. : Tape 1 2 3 4698U004AA NOTE Do not remove this part. [. . . ] Slowly move the Finisher away from the machine and open the Vertical Transport Section of the Finisher. 4698U009AA 4698N025AB <When Removing the Pipe> Using the tabs on the Finisher side, unlock the Pipe and pull it out from the mounting guide. Then, remove the Pipe together with the Feeder Attachment installed in step 3. Next, pull the Pipe out of the Feeder Attachment. 4643U019AB 4643U021AB 3. Remove the Lower Front Cover (two screws) of the Finisher. 4698-7744-03 ­3­ FINISHER 4. Pull up and remove the caster covers (two). Locking Bolt 7. After the check has been made, tighten the upper locking bolts of the casters (at four places), while holding the lower adjusting Adjusting Bolt bolts in position. Reinstall the parts which have been removed. 4643U020AA 4643U029AA s Connecting the Hookup Cord Locking Bolt Adjusting Bolt 5. Holding the lower adjusting bolt of the caster in position, loosen the upper locking bolt. Then, turn the lower adjusting bolt to adjust the height. <Two in the rear> If the Positioning Pin is higher : Turn the bolt clockwise. If the Positioning Pin is lower : Turn the bolt counterclockwise. <Two at the front> If Fixing Bracket A is higher : Turn the bolt clockwise. If Fixing Bracket A is lower : Turn the bolt counterclockwise. 4698U011AA · Connect the two connectors of the Hookup Cord of the Finisher at the locations shown. Then, screw the cover of the Hookup Cord with care not to allow any of the wires to be wedged by the cover. 4698U010AA 4643U022AB 4698U012AA 4698U028AA a 6. Press the Finisher against the machine and check that clearance between the two is equal at points a and b. NOTE If the clearance at a is not equal that at b, readjust with the casters. b 4698U027AA 4698-7744-03 ­4­ FINISHER s Installing the Tray and Wire Form · Install the Tray and Wire Form that come with the Finisher at the locations shown. · Install the cover furnished with the Finisher. (For the mounting screw, use the screw that has been removed in step 1 on p. 2. ) 4643U024AA 4643U034AA (For copier) Cover (For electronic document handler) 4643U035AA 4643U017AA 4698U035AB s Affixing the Labels Affix the labels that come with the Finisher. Label (for the copier) 4698U014AA Label (for the electronic document handler) 4698U015AA 4698-7744-03 ­5­ FINISHER s Setting the software DIP switches (For U. S. A. Plug the power cord of the machine in the power outlet and turn ON the Main Power Switch and Power Switch. Select "1" using the v or w key on the right or directly enter it from the 10-Key Pad. [. . . ] Press the Start key. 4698-7744-03 ­7­ FINISHER s Adjusting the Hole Positions for Hole Punch 8. Fold the copy in half to check that holes are in correct alignment with each other. Specifications: 0 ± 2 mm NOTE If the specifications are not met, adjust the hole positions for Hole Punch. Open the Top Cover of the Finisher and loosen the screw that secures the Hole Punch Guide Plate. [. . . ]