User manual KONICA MINOLTA FS-501 UNPACKING/SET-UP INSTRUCTIONS

[. . . ] <Machine + Paper Feed Cabinet PC-101/PC201> I Unpacking the Finisher 1. Check that the following accessories are available in the box. 1 Rail guide A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Rail guide B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 Ground plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 Rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5 Stabilizing pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 Magnet plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 7 Horizontal transport unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4684U058AA 9 Protective guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 <Machine + Paper Feed Cabinet PC-401> 10 Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 11 Screws A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 12 Screws B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 13 Installation manual (this manual) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 * 14 Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Rail Guide A is not used when the FS-501 is mounted on the machine (product code 4036). [. . . ] NOTE Slide out the rail to the left and check that it does not come off the Rail Guide B. Slide the other end of the rail installed in step 5 into the rail guide on the finisher. NOTE Insert the rail until it snaps into place. At this time, the finisher should stay attached to the machine, even if you try to pull it away. C4683U009AA 4583U017AB 3. Place the Ground Plate furnished with the kit in Rail Guide B. 4684U063AB C4683U010AA 4. Attach the rail guide B to the left side of the Paper Feed Unit as shown in the illustration (two screws B furnished with the finisher). NOTE Fit Rail Guide B in the tab on the lower portion of the Paper Feed Unit. 4684U064AA C4683U011AA ­4­ FS-501 I Unpacking the Horizontal Transport Unit Remove all packing materials and tape. I Adjusting the Height and Tilt of the Finisher 1. If the finisher gradually tilts toward the machine, check the following: · Are the stabilizing pin and the hole in the finisher at the same height?· Is the horizontal transport unit not extremely tilted?* 4684U066AA Tape C4651U023AB I Installing the Horizontal Transport Unit 1. Place the horizontal transport unit on the paper output section of the machine, and make sure that the plastic guide pin on the bottom of the horizontal transport unit hooks into the bracket on the finisher. If the finisher is not at the same height as the machine, adjust the machine as follows. 2. Slide the finisher away from the machine, and then remove the lower-front cover (two screws) of the finisher. C4683U023AA 4643U021AB 2. NOTE Make sure that the gears on the horizontal transport unit and on the finisher are correctly aligned. Lift the finisher's two caster covers up, and then pull them off. C4683U014AA 3. Secure the horizontal transport unit with the lock. NOTE Firmly secure the Horizontal Transport Unit and the Finisher in position using the Lock Lever. C4683U013AA 4643U020AA ­5­ FS-501 I Connecting the Hookup Cord Securing bolt Adjusting bolt 4. [. . . ] Label for Machine Label for RADF 4643U024AA C4683U018BA 4698U109AA for Machine for RADF 4643U017AA I Removing the Rail 1. Pinch together the rail stoppers on the left side of the finisher to release them. Remove the horizontal transport unit from the finisher, and then place it on top of the machine. [. . . ]