User manual KONICA MINOLTA IP304 INT V121

[. . . ] INSTRUCTION MANUAL IP-304 Read this manual before printing. Keep readily available for reference. Thank you very much for purchasing the IP-304. This INSTRUCTION MANUAL includes instructions for making prints, correct handling of the machine, and safety precautions. Please read this manual before printing. [. . . ] You can select any 8-digit number for the Password. Features Features use the special functions of the main body printer, with which you can set up the various printing and finishing method. When you select a function you would like to use from the upper list, the actual setting of the function you selected will be shown in the lower box. You can select the other setting of the function you selected from the list shown by clicking the [M] button of the lower box. Features you can select are as follows: Offset Staple Combination Punch Fold & Stitch Front Cover Front Cover Tray Back Cover Back Cover Tray Wait Mode Output Order Off / On None / Single Left / Double Top / Double Left None / Booklet / 2-in-1 Off / Left / Top None / Fold Only / Fold & Trim / Fold & Stitch / Fold, Stitch & Trim None / Printed / Blank None / Bypass tray / Bypass (Thick) / Tray1 / Tray2 / Tray3 / Tray4 / Tray5 / PI Tray None / Printed / Blank None / Bypass tray / Bypass (Thick) / Tray1 / Tray2 / Tray3 / Tray4 / Tray5 / PI Tray None / Wait / Wait with Proof Face Down / Face up 3-18 Print Controller INSTRUCTION MANUAL Chapter 3 Printer Driver Functions Features - Offset [On] offsets each copied set upon exit. In case of printing page 1, 2 and 3: page 1 page 2 page 3 3 sets 3 sets 2 sets 1 set 2 sets 3 sets 2 sets 1 set 1 set Offset OFF (Collate ON only) Offset ON (Collate ON) Offset ON (Collate OFF) [Offset] can not be performed in the following cases: · When Finisher is not available · When [B6] is selected in [Paper size] · When [Booklet] is selected in [Features] - [Combination] · When settings other than [None] are selected in [Features] - [Fold & Stitch] · When [Sub Tray] is selected in [Output Tray] Print Controller INSTRUCTION MANUAL 3-19 Chapter 3 Printer Driver Functions Features - Staple [Single-Left], [Double Top] or [Double Left] makes each stapled set of copies and output to the tray of the finisher. Stapling is performed as shown for the following orientations: Single Left (Portrait) Single Left (Landscape) Double Top (Portrait) Double Top (Landscape) Double Left (Portrait) Double Left (Landscape) [Staple] can not be performed in the following cases: · When Finisher is not available · When [A5], [B6] or [5. 5" x 8. 5"] is selected in [Paper size] · When [Thick paper] or [OHP [Transparency] is selected in [Media Type] · When [Collate] is not selected in [Copies] · When [Booklet] is selected in [Features] - [Combination] · When settings other than [None] are selected in [Features] - [Fold & Stitch] · When [Sub Tray] is selected in [Output Tray] · The following combination is selected e. g. , A3-size paper (portrait) and [Double Left] 3-20 Print Controller INSTRUCTION MANUAL Chapter 3 Printer Driver Functions Features - Combination The settings you can select are as follows: [None], [Booklet] or [2-in-1] Default is [None]. [Booklet] prints paper so that booklets are made when it is folded into two. 7 8 6 5 1 2 7 8 1 2 3 4 A4/B5/A5 A3/B4/A4 A3/B4/A4 [2 in 1] setting is available which prints out two page data on one sheet of paper. Two page data is printed out on a sheet of paper twice as large as the selected size of paper. 1 2 1 2 e. g. , 2 pages of A4-size paper Prints 2 pages onto a A3-size paper [Combination] can not be selected in the following cases: · When [On] is selected in [Features]-[Offset] [Booklet] can not be performed in the following cases: · When [Collate] is not selected in [Copies] · When [8. 5" x 14"], [11" x 17"], [A3], [B4] or [F4] is selected in [Paper size] · When [OHP [Transparency], [Thin paper] or [Thick paper] is selected in [Media Type] · When settings other than [None] are selected in [Features] - [Staple] · When settings other than [None] are selected in [Features] - [Back Cover] · When settings other than [None] are selected in [Duplex] Print Controller INSTRUCTION MANUAL 3-21 Chapter 3 Printer Driver Functions Features - Punch [Left], [Top] makes each punched set of copies and outputs to the tray of the finisher. However, this function is not usable when you selected Konica 7060/ 7150/Force 60 as the main body printer (i. e. [Konica IP-304(7060) PCL]). Punching is performed as shown for the following orientations: Left (Portrait) Left (Landscape) Top (Portrait) Top (Landscape) [Punch] can not be performed in the following cases: · When Finisher is not available · When [B6] is selected in [Paper size] · When [Thick paper] or [OHP [Transparency] is selected in [Media Type] · When [Collate] is not selected in [Copies] · When settings other than [None] are selected in [Features] - [Fold & Stitch] · When [Sub Tray] is selected in [Output Tray] · The following combination is selected e. g. , · When selecting the double stapling, punching and stapling are not set in the same direction. When selecting the single stapling, punching and stapling are set in the opposite direction. · Refer to the copier manual for more details on the stapling and punching combination. 3-22 Print Controller INSTRUCTION MANUAL Chapter 3 Printer Driver Functions Available paper size for punching / punching & stapling combination 2 holes Output Paper Size Punching 3 holes 4 holes Punching Punching Punching Punching Punching & Stapling & Stapling & Stapling A3 A4 A4R A5 B5 B5R B6 Japanese Postcard Letter (8. 5" x 11") Letter-R (8. 5" x 11") F4 Tabloid (11" x 17") Legal (8. 5" x 14") Statement (5. 5" x 8. 5") O O O O O O X X O O O O O O O O O O O O X X O O O O O O O O X X O X X X O X X O X X O O X X X X X X O X X O X X O O X X O X X X O X X O X X O O X X X X X X X X X X X X Print Controller INSTRUCTION MANUAL 3-23 Chapter 3 Printer Driver Functions Features - Fold & Stitch you can select the following finishing selections: [Fold Only] makes each folded set of copies and outputs to the tray of the finisher. [Fold & Trim] makes each folded set of copies and cuts off the excess part resulted from folding to maintain the paper size and outputs to the tray of the finisher. [Fold & Stitch] makes each folded and stitched set of copies and outputs to the tray of the finisher. [Fold, Stitch & Trim] makes each folded and stitched set of copies and cuts off the excess part resulted from folding to maintain the paper size and outputs to the tray of the finisher. Fold & Stitch Fold Only Fold, Stitch & Trim Fold & Trim Cutting off the excess part [Fold & Stitch] can not be performed in the following cases: · When [FS-108BM Finisher] is not available · When [Collate] is not selected in [Copies] · When [5. 5" x 8. 5"], [A5], [B5], [B6] or [F4] is selected in [Paper size] · When [OHP [Transparency] or [Thick paper] is selected in [Media Type] · When [On] is selected in [Features]-[Offset] · When [On] is selected in [Features]-[Staple] [Fold & Trim] or [Fold, Stitch & Trim] can not be performed in the following cases: · When [TU-108 Trimmer Unit] is not available 3-24 Print Controller INSTRUCTION MANUAL Chapter 3 Printer Driver Functions Features - Front Cover You can select this setting when using for the front covers a different paper from that of the body of the booklet (colored one, for example). [Front Cover] inserts a sheet to the top of each set of copies as a Front cover. The settings you can select are as follows: [None], [Printed] or [Blank] Default is [None]. · When [Blank] is selected, nothing is printed on the front cover. · When [Printed] is selected, the first page data is printed on the front cover. None Printed Blank [Front Cover] can not be performed in the following cases: · When [Collate] is not selected in [Copies] · When [2-in-1] is selected in [Features] - [Combination] · When [OHP [Transparency], [Thin paper] or [Thick paper] is selected in [Media Type] Features - Front Cover Tray Specify the paper tray for the front cover. The settings you can select are as follows: [None], [Bypass tray], [Bypass (Thick)], [Tray 1], [Tray 2], [Tray 3], [Tray 4], [Tray 5] or [PI Tray] Default is [None]. [Front Cover Tray] can not be performed in the following cases: · When [None] is selected in [Features] - [Front Cover] [PI Tray] can not be performed in the following cases: · When [FS-108BM Finisher] is not available · When [PI-108 Sheet Feeder] is not available Print Controller INSTRUCTION MANUAL 3-25 Chapter 3 Printer Driver Functions Features - Back Cover You can select this setting when using a different paper from that of the body of the booklet for example, colored one, for the back cover. The settings you can select are as follows: [None], [Printed] or [Blank] Default is [None]. · When [Blank] is selected, nothing is printed on the back cover. · When [Printed] is selected, the last page data is printed on the back cover. None Printed Blank [Back Cover] can not be performed in the following cases: · When [Collate] is not selected in [Copies] · When [2-in-1] is selected in [Features] - [Combination] · When [Booklet] is selected in [Features] - [Combination] · When [OHP [Transparency], [Thin paper] or [Thick paper] is selected in [Media Type] Features - Back Cover Tray Specify the paper tray for the back cover. The settings you can select are as follows: [None], [Bypass tray], [Bypass (Thick)], [Tray 1], [Tray 2], [Tray 3], [Tray 4], [Tray 5] or [PI Tray] Default is [None]. [Back Cover Tray] can not be performed in the following cases: · When [None] is selected in [Features] - [Back Cover] 3-26 Print Controller INSTRUCTION MANUAL Chapter 3 Printer Driver Functions [PI Tray] can not be performed in the following cases: · When [FS-108BM Finisher] is not available · When [PI-108 Sheet Feeder] is not available e. g. , Setting of [Front Cover / Back Cover] Front Cover + Back Cover Front Cover Front Cover Front Cover /Back Cover Front Cover / Back Cover (PI Tray) + Fold Only (Features) Front Cover / Back Cover (PI Tray) + Fold & Stitch (Features) (option) Features - Wait Mode [Wait] enables checking of the current job settings on the LCD touch screen of the main body printer [Wait with Proof] enables checking of the current job settings on the LCD touch screen of the main body printer and to see how the printed job will look before printing out multiple sets. Refer to "Chapter 4 Control Panel Setup, Print Job - Check" (p. 4-16). Output Order Select a direction of paper ejection, [Face Down] or [Face Up]. This function is usable when you selected Konica 7060/7150/Force 60 as the main body printer (i. e. [Konica IP-304(7060) PCL]). Face Down Face Up Restore Defaults By clicking the [Restore Defaults] button, the [Paper] tab settings return to defaults. Print Controller INSTRUCTION MANUAL 3-27 Chapter 3 Printer Driver Functions [Graphics] Tab Halftoning You can select [Patterned Grays], [Solid Black and White] or [Diffused Grays] by clicking the radio button. [Patterned Grays] prints image by an ordered dither algorithm. [Solid Black and White] prints without dithering and gray tone. [. . . ] 3-30 P Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Page Description Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 Paper Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15 Paper Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]